BOLD MAGENTA part numbers are new for 2023 DRAGSPECIALTIES.COM 2023 | TIRE & SERVICE V-TWIN TOOLS 616 PART # DESCRIPTION SUG. RETAIL DS196277 For Twin Cam, .927” wrist pin $35.95 DS-196094 For Evolution, .791” wrist pin 35.95 ROD ALIGNMENT TOOLS • Use to check rod straightness without removing the rods from the cases • Alignment tool is 4.5” long • Available in Twin Cam and Evolution applications • Made in the U.S.A. DS196277 DS-196094 PART # DESCRIPTION SUG. RETAIL DS-196159 For 36-99 Big Twin, 57-20 XL and Buell (except 1125R) $165.95 PISTON PIN BUSHING TOOL • Use to remove and install wrist pin bushings without removing rods from crankcase • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0045 Stud assembly tool $75.95 EVOLUTION CYLINDER STUD ASSEMBLY TOOL • Assembly tool features a captive hardened ball bearing dimensionally set 1” from top of tool • Made of high-tensile steel • Works on all Evolution Big Twin and XL models • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3850-0121 For 84-17 Big Twin (except M-Eight) and 86-20 XL $57.95 EXHAUST GASKET SEAL INSTALLER TOOL • Installs fragile exhaust seal with ease and will position seal evenly to exhaust port of head • Can be used with exhaust flange nuts or JIMS handle PART #DS-196042; sold separately • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3850-0227 Exhaust ring retainer tool $105.95 EXHAUST RING RETAINER TOOL • Quickly and easily installs the exhaust pipe retaining ring on almost all H-D exhaust systems • Install the H-D #65325-83A ring in seconds, without scratching the exhaust pipe or twisting the ring • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196039 5/16” stud installation tool $27.95 5/16” STUD INSTALLATION TOOL • Designed to set Twin Cam and Evolution exhaust studs, Shovelhead rocker box studs, 4-speed transmission end studs, Bendix & Keihin carb flange studs and most other 5/16” studs • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0199 For Evolution Big Twin, Sportster and Twin Cam w/ 3/8” stud $46.95 CYLINDER SLEEVE HOLD-DOWNS • Specialty nuts are used to hold down cylinder sleeves during service • Allow motor to be turned over with heads off • Nuts fit 3/8”-16 UNC thread • Feature 3/4” hexagon with a small cylinder protruding down to catch the cylinder stud • Case-hardened and zinc-plated • Sold in 4-pack PART # DESCRIPTION SUG. RETAIL 3850-0161 For 99-17 Dyna $36.95 EXHAUST BRACKET WRENCH • To remove and install the front exhaust bracket • 9 3/4” L; single end with reversible ratcheting action • Removable/replaceable shortened T-27 Torx bit • Low-profile design allows for easy access to the exhaust bracket in between the frame and engine • Vinyl grip protects bike from damage during use and provides an ergonomic grip PART # DESCRIPTION SUG. RETAIL DS-197032 For 84-17 Big Twin (except M-Eight), 86-20 XL and 94-09 Buell (except 1125R) $154.95 EXHAUST STUD DRILL PLATE • Designed to drill broken exhaust studs • Can be used with most motors still in the frame • Includes drill bushing and 1/4” drill bit • Made in the U.S.A.
RkJQdWJsaXNoZXIy OTcxOTk3