BOLD MAGENTA part numbers are new for 2024 V-TWIN TOOLS DRAGSPECIALTIES.COM TIRE & SERVICE | 2024 611 PART # DESCRIPTION SUG. RETAIL 3801-0316 For 17-20 M-Eight $360.95 CAMSHAFT NEEDLE BEARING REMOVER/INSTALLER •Correctly and accurately replaces the camshaft inner needle bearing in M-Eight engines •Uses the proven JIMS-style remover collet and fine-threaded installation driver •Removal hole allows you to see what you’re doing while using the tool • Holds tighter tolerances, allowing more precise installation depth •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196199 For 99-06 Twin Cam (except 06 Dyna) for removing/ installing cams and bearings; for 00-06 FXST/FL and L00-05 FXD to remove and install cams only $263.95 CAMSHAFT REMOVAL/ INSTALLATION TOOL •Used to remove and install camshafts and bearings •Provides precision alignment of camshafts in the support plate •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0066 For 06 Dyna and all 07-17 Twin Cam $233.95 CAM ASSEMBLY TOOL •Holds both cams in an upright position while lowering cam support plate over both guides and cam journal guides •Made from a non-marring material that will not damage cam surface •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196193 For 99-06 Twin Cam (except 06 Dyna) for removal of bearings; for L00-06 FXST/FL and L00-05 FXD for removal of front cam bearing $325.95 CAM BEARING PULLER •Use to remove the cam ball bearings from the camshafts after they are removed from the support plate •Removes bearing straight without binding or slipping •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0061 For 06 Dyna and all 07-17 Twin Cam $358.95 DS-196198 For 00-06 Twin Cam motors (except 06 FXD) 240.95 DS-196156 For 58-99 Big Twin, except Twin Cam 252.95 DS-197056 For 57-90 XL 251.95 INNER CAM BEARING REMOVAL TOOLS •Used to remove inner cam bearing without damaging the crankcase •Tool is also designed to keep rollers from falling into the crankcase •Instructions included •Made in the U.S.A. 3801-0061 PART # DESCRIPTION SUG. RETAIL DS-196170 For 70-99 74” and 80” Big Twins, and 70-03 XL models $21.95 CAM COVER PULLER •Designed to remove the cam cover •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196144 For 70-99 Big Twin (except Twin Cam) $138.95 CAM COVER HOLDING TOOL •Clamps in vise •Holds cam cover flat and helps prevent damage/ scratches when removing and installing bushings •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0252 For 17-23 M-Eight oil pumps and 99-17 Twin Cam camplates $119.95 REAMER TOOL FOR PSI RELIEF VALVE BORE • Use this reamer to perform a ‘valve job’ on the pressure relief valve seat of all M-Eight oil pumps and Twin Cam engine camplates •Lightly machine (clean) the relief valve seat and re-seat the plunger valve •Feuling recommends the valve to be seated and sealed from 0-30 psi with a full pop off psi of 55-60 psi •Best used in conjunction with Feuling® pressure testing tool PART #3801-0071 for Twin Cam camplates •Made in the U.S.A.
RkJQdWJsaXNoZXIy OTcxOTk3