BOLD MAGENTA part numbers are new for 2024 PARTS-UNLIMITED.COM 2024 | STREET EXHAUST 88 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. LENGTH PART # SUG. RETAIL 38mm M7713 $17.95 57mm M7714 17.95 60mm M7715 17.95 LENGTH PART # SUG. RETAIL 63mm M7709 $17.95 67mm M7710 17.95 70mm M7716 17.95 LENGTH PART # SUG. RETAIL 75mm M7711 $17.95 80mm M7717 17.95 83mm M7712 17.95 LENGTH PART # SUG. RETAIL 90mm M7718 $17.95 95mm M7719 17.95 100mm M7720 17.95 EXHAUST SPRINGS •Stainless steel construction gives superior strength and attractive appearance •Swivel hook design eliminates binding, extending spring life •Available for most late-model 2-stroke and 4-stroke models •Made in the U.S.A. •Sold in pairs NOTE: When measuring for exhaust spring length, please use points #1 - #3 for reference. 1. Exhaust springs should be measured when they are off the vehicle.Wear eye protection when removing. 2. The length measurement should be taken from inside hook to opposite end inside of hook. 3. For correct fit, an exhaust spring should not be extended more than 20% of its free length. DESCRIPTION PART # SUG. RETAIL 57mm (pr.) 1860-2372 $8.19 57mm (10-pk.) 1860-2373 33.06 60mm (pr.) 1860-2374 8.19 60mm (10-pk.) 1860-2375 33.06 63mm (pr.) 1860-2376 8.19 63mm (10-pk.) 1860-2377 33.06 67mm (pr.) 1860-2378 8.19 67mm (10-pk.) 1860-2379 33.06 70mm (pr.) 1860-2380 8.19 70mm (10-pk.) 1860-2381 33.06 DESCRIPTION PART # SUG. RETAIL 75mm (pr.) 1860-2382 $8.19 75mm (10-pk.) 1860-2383 33.06 80mm (pr.) 1860-2384 8.19 80mm (10-pk.) 1860-2385 33.06 83mm (pr.) 1860-2386 8.19 83mm (10-pk.) 1860-2387 33.06 90mm (pr.) 1860-2388 8.19 90mm (10-pk.) 1860-2389 33.06 95mm (pr.) 1860-2390 8.19 95mm (10-pk.) 1860-2391 33.06 EXHAUST SPRINGS • High quality, zinc-plated tempered spring wire •Sold in various quantities; please see chart DESCRIPTION PART # SUG. RETAIL 3” L hanger bracket DS-203060 $8.95 4 3/4” L hanger bracket DS-203070 8.95 EXHAUST HANGER BRACKETS •Chromed 1/8” thick steel exhaust hangers •Sold each DESCRIPTION PART # SUG. RETAIL For 1 3/4” OD pipes; 8” L 1861-0739 $13.95 For 2” OD pipes; 9 3/4” L 1861-0913 13.95 For 2” OD pipes; 6” L 1861-1190 13.95 For 2 1/4” OD pipes; 8 1/4” L 1861-0914 13.95 For 2 1/2” OD pipes; 8 1/2” L 1861-0915 16.95 For 3” OD pipes; 8” L 1861-0916 16.95 EXHAUST BAFFLES • Fiberglass-wrapped steel construction •Available for a variety of pipe sizes •May require drilling a hole in the exhaust pipe •Sold each DESCRIPTION QTY. PART # SUG. RETAIL 1 3/4” ID Ea. DS-202011 $52.95 1 3/4” ID Pr. DS-202012 98.95 2” ID Pr. DS-202032 98.95 HP-PLUS™ DRAG PIPE BAFFLES •Dampen sound without impeding flow-through performance •All-steel construction; baffles feature patented HP-PLUS™ design •Install easily on 1 3/4” or 2”, 16- or 18-gauge drag pipes •Baffles held by 1/4”-20 screws and locking nuts •Sold in pairs or each •Made in the U.S.A. INLET DIA. LEFT/RIGHT PART # SUG. RETAIL KH 2.5” R KE-6400S $214.95 KI 2.5” R KE-6400S 214.95 KK 2.5” R KE-6400S 214.95 KL 2.5” L KE-6400S 214.95 COMPETITION BAFFLE WITH END CAP •Large competition baffles provide low restriction for competition use; may not meet street sound level test requirements • Pre-wrapped; include 2.5” end cap • When ordering replacement baffle, check your exhaust system silencer ID number (located on inlet under clamp) •Sold each DS-202012 DS-202011 DESCRIPTION PART # SUG. RETAIL 100mm (pr.) 1860-2392 $8.19 100mm (10-pk.) 1860-2393 33.06 Dealer kit 1860-2394 135.67 1860-2372 1861-0739 DS-203060 DS-203070
RkJQdWJsaXNoZXIy OTcxOTk3