BOLD MAGENTA part numbers are new for 2025 FUEL/AIR SYSTEMS PARTS-UNLIMITED.COM STREET | 2025 FUEL/AIR SYSTEMS 1475 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. DQS APPLICATIONS FITS MODEL QUICK SHIFT SENSOR TYPE DUAL CONTACT SENSOR TYPE SHIFT ROD TYPE APRILIA RSV Mille 04-09 1601-0014 - - RST 1000 Futura 01-05 1601-0014 - - Tuono 03-05 1601-0014 - - BMW S1000R 14-16 - 1601-0510 - S1000RR 10-18 - 1601-0510 - DUCATI 749/S 03-06 1601-0014 - 1601-0016 848 08-10 - 1601-0512 1601-0016 M800 Monster 03-04 - 1601-0512 1601-0016 M900 Monster 00-01 - 1601-0512 1601-0016 999/S 03-06 1601-0014 - 1601-0016 DS1000 Monster 03-04 - 1601-0512 1601-0016 1098/R 07-08 - 1601-0512 1601-0016 HONDA CB500/CBR500R 13-18 - 1601-0510 - CBR600F4i 01-06 - 1601-0510 1601-0017 CBR600RR 03-20 - 1601-0510 1601-00161 CB650F/CBR650F 14-18 - 1601-0510 - FITS MODEL QUICK SHIFT SENSOR TYPE DUAL CONTACT SENSOR TYPE SHIFT ROD TYPE HONDA (CONT) CB650R/CB650RR 19-20 - 1601-0510 - NC700X 12 - 1601-0510 1601-00161 CBR929RR 00-01 - 1601-0510 1601-0016 CBR954RR 02-03 - 1601-0510 - CB1000R 08-19 - 1601-0510 - CBR1000RR 04-19 - 1601-0510 1601-00161 RC51 00-06 1601-0247 - - KAWASAKI EX300 13-17 - 1601-0510 - ZX6R 03-04 - 1601-0512 1601-0016 ZX6R 05-06 - 1601-0510 1601-0017 ZX6R 07-20 - 1601-0510 1601-00161, 2 ZX6RR 03 - 1601-0512 1601-0016 ZX6RR 04 - 1601-0512 1601-0016 ZX6RR 05-06 - 1601-0510 1601-0017 DYNOJET QUICK SHIFTER (DQS) SENSORS USB/V •Races are won or lost in fractions of a second • Dynojet’s Quick Shifter (DQS) kit allows full-throttle, clutchless upshifts in racing and performance riding applications •Shift rod pressure/tension sensor kit is a universal sensor that mounts to the shift rod in either a push or pull configuration; requires modification of gear-linkage tie rod •Linear travel sensor kit works with bikes that have no shift rod, or on those the shift rod sensor will not fit, by mounting one end to the shift lever and the other to a fixed point on the chassis; available in push or pull types with universal mounting hardware •Plugs directly into the Power Commander expansion port with no rewiring required •Power Commander Control Center software lets you set engine dead time during upshifts and minimum rpm for system operation • PART# 1601-0510 and 1601-0512 “pressure style” sensors for PCV/USB and have two terminals, so it can either act as “push” or “pull” type • PART# 1601-0014 is a “linear” sensor for PCIII USB • PART# 1601-0247 is a “linear” sensor for PCV NOTE: To order either of the above sensors, you must find the correct direction of movement during an upshift (push or pull). For the shift rod/pressure/tension sensor, press on the shift lever in the direction of an upshift to see if the rod is pushing or pulling on the clevis on the shift shaft. For the linear travel sensor, also move the shifter for an upshift. If movement is down, a pull sensor is needed. If movement is up, a push sensor is required. 1601-0553 DESCRIPTION PART # For most Honda and Suzuki models 1601-0553 DESCRIPTION PART # For most Kawasaki and Yamaha models 1601-0554 STANDALONE QUICKSHIFTER MODULES •Easy plug-and-play installation •No computer necessary for adjustment •Intellishift technology adapts while riding 1601-0014 1601-0512 DYNOJET QUICK SHITER (DQS) SENSORS USB/V continued on next page. 1 Requires either a Quick Shifter Expansion Module (QEM), Secondary Fuel Module (SFM) or an Ignition Module to use the DQS. See page 1475 for QEM and SFM; see page 1476 for Ignition Modules. ZX10R 11-15 must also order shift rod C PART #1601-0018. 2 Not for ZX6R 13-15.
RkJQdWJsaXNoZXIy OTcxOTk3