UPDATE 2026
The 2026 Drag Specialties/Parts Unlimited Update catalog is here! We’ve been hard at work to bring you the latest parts and accessories.And we make sure every item in the Update catalog is supported with the latest technical and fitment information. Combine this catalog with your current 2026 Parts Unlimited and Drag Specialties catalogs to give your sales a strong midyear boost. We continue to add new products throughout the year. Be sure to check out parts-unlimited.com and dragspecialties.com for the latest parts, accessories and gear from Parts Unlimited and Drag Specialties. Parts Unlimited and Drag Specialties – Supporting the dealer, the customer and the entire sport! All model designations and applications used herein are determined by the manufacturers as USA-specific. Contact the individual manufacturer for additional international model information. 2 ADDING TO THE EXCITEMENT IN 2026 • OLDBOOK • FATBOOK • INDIAN • STREET • OFFROAD • ATV/UTV • BICYCLE • SNOWMOBILE • WATERCRAFT • HELMET & APPAREL • TIRE & SERVICE OldBook..................... 7-31 FatBook................... 32-141 Indian................... 142-153 Street. .................. 154-210 Offroad................... 211-281 ATV/UTV................... 282-308 Snow.................... 309-320 Watercraft................. 321-322 Bicycle................... 323-324 Helmet & Apparel. ........... 325-600 Tire & Service.............. 601-624 Index.................... 625-642 WE SUPPORT THE SPORT®
3 IMPORTANT INFORMATION: EMISSIONS REGULATIONS NOTE: The California Air Resources Board (“CARB”) does not permit the use of aftermarket emissions-related part(s) that alter the performance of OEM emissions-related devices unless CARB has issued an Executive Order, other than on racing vehicles on closed courses. Check your local laws and manufacturer’s information. More California exhaust information is available at www.arb.ca.gov/. NOTE: Parts designated as “Race Only” are for use only on vehicles used for competition racing and are not for use on vehicles registered for use on public roads. Sale and/or installation of “Race Only” parts in any way inconsistent with this warning is prohibited and may result in enforcement by the U.S. EPA under the federal Clean Air Act. “RACE ONLY” PARTS ARE NOT LEGAL FOR SALE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES. NOTE: Aftermarket products, including but not limited to exhausts, catalytic converters, oxygen sensors, fuel/a ir controller modules, air filter kits, camshafts, O2 eliminators, and carburetors and jet kits which alter, modify, or replace emission control devices or systems of an originally compliant highway motorcycle, are not legal for sale or street use in California unless they have been issued a CARB Executive Order. Aftermarket emissions-related products which have not been issued an Executive Order or which are not aftermarket Replacement Parts, as defined in Title 13, California Code of Regulations, Section 1900(b)(2), are authorized for closed circuit race use only. Products shown may be designed, manufactured, intended and sold for closed circuit race use only and use of the same on public roads or lands may be a violation of local, state and/or federal laws. See manufacturer’s information and state and local laws to determine what is authorized for your use on your vehicle. The following emissions-related defined terms are used in this catalog (PARTS WITH THE FOLLOWING DESIGNATIONS IN THIS CATALOG ARE NOT ILLEGAL FOR SALE IN CALIFORNIA UNDER CARB REGULATIONS): • “CARB E.O.” means the specified Executive Order issued by CARB. An Executive Order constitutes an exemption by CARB from CA Vehicle Code 27156 and 38391, for sale of the part number for the make/model/year fitment(s) specified in the Executive Order. • “Replacement Part” means any aftermarket part intended to replace an original equipment emissions-related part and which is functionally identical to the original equipment part in all respects which in any way affect emissions (including durability), or a consolidated part. • “Qualified Manufacturer Declared Replacement Part” means any aftermarket part intended to replace an original equipment emissions related part and which is functionally identical to the original equipment part in all respects which in any way affect emissions (including durability), or a consolidated part, that has been evaluated and declared by the manufacturer to meet this definition and carry this categorization and designation label. This manufacturer has declared in writing that it has documentation, based upon sound engineering judgment, indicating the replacement part does not reduce the effectiveness of any required emission control device and it does not cause the modified vehicle/engine/equipment to exceed applicable emissions standards for that make/model/year fitment(s) advertised. In addition, for 49-State compliance, the following term applies: • “Qualified Manufacturer Declared 49-State Federal Emissions Compliant Part” (Not legal for sale or use in California) means any aftermarket part intended to replace an original equipment emissions-related part and that meets all EPA emission regulations by installing the element of design in all emissions-related respects to the certified configuration of the vehicle, engine, or piece of equipment. This manufacturer has declared in writing that it has fully documented the emissions testing of an appropriate test vehicle, engine, or piece of equipment that had been identically altered and that the part meets all applicable emissions standards for that make/model/year fitment(s) advertised.
4 SEMA CATEGORIZATION LABELS IMPORTANT INFORMATION: EMISSIONS PRODUCT CATEGORIZATION This catalog implements use of a categorization system developed by SEMA to identify emission products’ classifications and any corresponding restrictions on sales of those products. The products will be identified as fitting one of the following categories, as determined by the vendor/manufacturer. The categorization system is set forth below. The applicable product classification is displayed under the “EMIS” column in the catalog. Category Meaning Sales Restrictions 1 This Product is covered under a CARB EO and is legal for sale and use in all 50 states. See “CARB EO” definition on page 3. No USA Territory Restrictions. 2 This product is covered under a SEMA Certified Emissions certification or has otherwise met the requirements of the EPA’s Tampering Policy and is legal for sale in states that do not mandate an EO. See “Qualified Manufacturer Declared 49-State Federal Emissions Compliant Part” definition on page 3. Blocked from sales into California. 3 This product is not legal for street use on an emissions-controlled vehicle. It may be used on dedicated competition or pre-pollution-controlled vehicles only. See “Race Only” Note on page 3. *Products for which vendors did not supply classification information are by default coded as “3.” Blocked from sales in ALL states unless dealer signs acknowledgment of dealer’s obligation to ensure sales or installation of such parts are on “Competition Use” only vehicles and not for highway use. 4 This product does not require an EO in California. By nature of its design, it is legal for sale and use in all 50 states. Replacement parts included. See “Qualified Manufacturer Declared Replacement Part”definition on page 3. No USA Territory Restrictions. N/A Product not subject to emissions control regulations. No USA Territory Restrictions.
5 IMPORTANT INFORMATION: SALES OF RACE ONLY PARTS The federal Environmental Protection Agency’s policies related to tampering and defeat devices are publicly available at the following sites: https://www.epa.gov/sites/production/files/2020-12/documents/ epatamperingpolicy-enforcementpolicyonvehicleandenginetampering.pdf https://www.epa.gov/sites/production/files/2020-12/documents/ tamperinganddefeatdevices-enfalert.pdf https://www.epa.gov/sites/production/files/2021-01/ documents/caatitleiivehicleenginepenaltypolicy011821.pdf The EPA has taken civil and criminal enforcement action against companies and individuals for violations of the Clean Air Act’s tampering and defeat device prohibitions. By ordering “Race Only” parts from LeMans Corporation, d/b/a Parts Unlimited® and Drag Specialties® (“LeMans”), you, as the selling retailer, expressly acknowledge and assume all the responsibility for ensuring and documenting information to verify that the sale or installation of every “Race Only” part is for competition racing vehicle use only. Examples of such documentation include: • Require that the buyer of the part(s) sign an acknowledgement that the part is for “Race Use Only.” The acknowledgement would contain enough information (i.e., invoice number, purchase date, purchaser name, part number, etc.) to be able to track the part to its ultimate installation. • Evidence that the vehicle is not registered in any State for highway use. • The detailed owner or operator information and vehicle VIN are recorded. • The vehicle is being used in only closed course competition events like King of the Baggers®, BRL Bagger Racing League®, SUPER HOOLIGAN®, AMA FLAT TRACK®, or one of the hundreds of similar competition racing use only events throughout the US (road race, flat track, drag racing and land speed). If you have questions regarding the information that you should collect as evidence that the part purchased from LeMans and sold or installed by you/your company will be used only on a “Race Only” vehicle as intended, please refer to your legal counsel or racing trade association. When ordering Race Only products from LeMans, you will be required to provide a signed Acknowledgement confirming: 1. You are solely responsible to verify and document that use of “Race Only” parts will be limited to competition racing use consistent with the terms of this notice on each individual sales transaction; 2. You will provide LeMans with copies of the documentation that shows evidence of the use of “Race Only” parts purchased from LeMans upon request; and 3. You consent to the disclosure of your identity to any governmental entity responsible for regulating emissions and/or enforcing emissions laws, if requested. NOISE REGULATIONS A number of jurisdictions/states have exhaust noise laws. Exhaust products advertised might not be legal for sale or use on highway vehicles in such jurisdictions/states. Check applicable laws and regulations.
6 IMPROPERLY FITTING PRODUCTS COULD CONTRIBUTE TO SERIOUS INJURY OR DEATH. SAFETY WARNING: Riding a motorcycle, snowmobile, ATV/UTV, watercraft or bicycle is a dangerous activity. When riding, always wear a helmet, eye protection and protective clothing. There is no assurance that serious injury or death can be avoided even if you wear the product shown in this catalog and take all precautions to avoid every risk. Please ensure that your products fit properly. Improperly fitting products can impair your ability to control your motorcycle, snowmobile, ATV/UTV, watercraft or bicycle. HELMET FITMENT: Helmet fit is critical to helmet performance. The correct helmet size can only be checked and confirmed by physically fitting the helmet to the user. Always try the helmet on in a store, before purchasing it, to be sure you are purchasing the correct sized helmet for you. Ask your dealer for more information. WARNING
7 Update
BLUE part numbers are new for 2026 PARTS-UNLIMITED.COM 2026-2027 | OLDBOOK UPDATE AUDIO, COMMUNICATION & MOUNTS SECTION 2 OLDBOOK 8 GEN 2 ACCESSORY MIRROR MOUNT •Can be installed on left or right mirror stem with 3/8” or 9.5 mm stem size •360° swivel in two directions •Comes in black finish •Fully adjustable and compatible with Ciro® Gen 1 or Gen 2 ball mount accessories (sold separately) •See page 77 of the 2026-2027 Drag Specialties OldBook for the complete line of Ciro® Gen 2 Accessory Mounts PART # DESCRIPTION FOR ALL 96-99 H-D MODELS 0636-0710 Black mirror mount for left or right mirror stem nut with 3/8” or 9.5 mm stem size SPC+ XTREME PHONE CASES •Rugged and waterproof cases •360° protection for your phone or digital device in any terrain •Integrated locking mechanism and magnets for easy attachment •Magsafe®-compatible for quick and convenient charging on the go PART # DESCRIPTION 0636-0698 iPhone 17 PART # DESCRIPTION 0636-0699 iPhone 17 Pro PART # DESCRIPTION 0636-0700 iPhone 17 Pro Air PART # DESCRIPTION 0636-0701 iPhone 17 Pro Max SPC+ PHONE CASES •Securely mounts to any SP Connect™ holder in just one second • Thanks to a 40% thinner design, the SPC+ model is fully MagSafe®-compatible •Ready for inductive charging and magnetic attachment •See pages 95-97 of the 2026-2027 Drag Specialties OldBook for the complete line of SPC+ Phone Cases PART # DESCRIPTION 0636-0702 Google® Pixel 10/Pro 0636-0703 Google Pixel 10 Pro XL PART # DESCRIPTION 0636-0694 iPhone 17 0636-0696 iPhone 17 Air PART # DESCRIPTION 0636-0695 iPhone 17 Pro 0636-0697 iPhone 17 Pro Max •Full touchscreen usability (works with a glass screen protector) •Additional camera lens protection •See pages 94-95 of the 2026-2027 Drag Specialties OldBook for the complete line of SPC+ Xtreme Phone Cases 0636-0698 0636-0699 0636-0700 0636-0701 0636-0694 0636-0695 0636-0696 0636-0697 0636-0702 0636-0703
BLUE part numbers are new for 2026 SADDLEBAGS & LUGGAGE DRAGSPECIALTIES.COM OLDBOOK UPDATE | 2026-2027 SECTION 3 OLDBOOK 9 ARMADILLO BAGS® • Flexible, collapsible, lightweight, expedition-ready utility bladders •Provides safe transport and storage of liquid hydrocarbon products and other powersport and automotive fluids •Includes pour spout •See page 178 of the 2026-2027 Drag Specialties OldBook for the complete line of Armadillo Bags® PART # DESCRIPTION 3510-0215 1-gallon PART # DESCRIPTION 3510-0216 2-gallon PART # DESCRIPTION 3510-0217 3-gallon PART # DESCRIPTION 3510-0218 5-gallon CACTUS CANTEEN™ • Ultra-lightweight, rugged, collapsible container for transporting drinking water •Integrates with Giant Loop’s adventure proof packing system • Comes equipped with a versatile dispensing system, high visibility daisy chains, and a universal wide mouth cap •The perfect solution to keep you going wherever the trail leads you •See page 178 of the 2026-2027 Drag Specialties OldBook for the complete line of Cactus Canteen™ PART # DESCRIPTION 3519-0157 1-gallon PART # DESCRIPTION 3519-0158 2-gallon NOTE: Not a portable fuel container as described by ASTM, EPA,ARB or other state and federal agencies. NOTE: Not recommend for use of potable drinking water without filtration. 3510-0216 3510-0217 3510-0218 3510-0215 3519-0157 3519-0158
BLUE part numbers are new for 2027 PARTS-UNLIMITED.COM 2026-2027 | OLDBOOK UPDATE SEATS & SISSY BARS SECTION 4 OLDBOOK 10 FOR DRESSER/TOURING SQUAREBACK 2-UP SEAT •Delivers an updated style to a classic look for H-D • A low-cut 11.5” driver bucket rises to meet the squared-off passenger section, offering good back support •The generous width of the passenger section gives great support for two-up riding while maintaining a sporty look •Handsewn cover features a Double Diamond pattern •Mustang’s proprietary controlled-density foam formula requires no break-in and retains shape and support after years of use •Marine-grade fiberglass baseplate for long-lasting support and durability, with polyurethane bumpers to absorb vibration •Made in the U.S.A. PART # DESCRIPTION FOR 97-98 FLHT/FLTR (13 1/2” DRIVER SEAT AREA, 8” PASSENGER SEAT AREA) 0801-2125 11.5” W driver; 8.5” W rear HIGHNOON 2-UP SEATS •Features a 7 1/2” tall driver support with unique styling •Made from Slip Stop™ high-quality PVC material in the seating area and high-quality automotive-grade vinyl on the sides •Slip Stop high-quality PVC material is designed with gripping qualities to reduce slippage •Molded polyurethane foam for maximum comfort and styling •3/16”ABS thermoformed seat base for a perfect fit, with a carpeted bottom and rubber bumpers to protect paint •Includes all mounting hardware •Made in the U.S.A. PART # DESCRIPTION FOR 97-98 FLHR; 31” L OVERALL (11 1/2”W FRONT X 7”W REAR) 0801-2148 Double diamond, black thread w/ Slip Stop™, and black logo PART # DESCRIPTION FOR 97-98 FLHR; 31” L OVERALL (11 1/2”W FRONT X 7”W REAR) (CONT) 0801-2149 Double diamond, gray thread w/ Slip Stop, and gray logo RAIN COVERS • Convenient, easy-to-use design •Folds into itself for storage •Highly water-resistant construction •Protects expensive seats from sun damage or rain •Great for RoadSofa™, Step-Up™ or Touring seat models • Touring models fit most full-size seats up to 38” L x 18”W • Step-Up models fit Step-Up, smaller RoadSofa and seats up 30” L x 15 to 18”W and include cover for Tour-Pak •Available to fit seats with or without driver’s backrest PART # DESCRIPTION 0821-3648 For Touring seats w/o driver’s backrest 0821-3649 For Touring seats w/ driver’s backrest PART # DESCRIPTION 0821-37001 For Step-Up™ and smaller seats w/o driver’s backrest 0821-37011 For Step-Up and smaller seats w/ driver’s backrest 1 Includes rain cover for Tour-Pak. 0801-2149 0821-3649
BLUE part numbers are new for 2026 SEATS & SISSY BARS DRAGSPECIALTIES.COM OLDBOOK UPDATE | 2026-2027 SECTION 4 OLDBOOK 11 FOR DYNA GLIDE HIGHNOON 2-UP SEATS • Features a 7” tall driver support with unique styling •Made from Slip Stop™ high-quality PVC material in the seating area and high-quality automotive-grade vinyl on the sides •Slip Stop high-quality PVC material is designed with gripping qualities to reduce slippage •Molded polyurethane foam for maximum comfort and styling PART # DESCRIPTION FOR 96-98 FXD/FXDL/FXDS/FXDWG; 31” L OVERALL (11 1/2”W FRONT X 7”W REAR) 0803-0765 Double diamond, black thread w/ Slip Stop™, and black logo PART # DESCRIPTION FOR 96-98 FXD/FXDL/FXDS/FXDWG; 31” L OVERALL (11 1/2”W FRONT X 7”W REAR) (CONT) 0803-0766 Double diamond, gray thread w/ Slip Stop, and gray logo PRO SERIES SDC PERFORMANCE GRIPPER SEATS •True performance-oriented comfort seats with contoured lines, bucketed driver’s seating area and substantial lumbar support • Crafted with carbon fiber (CF) at the front, black gripper on the lumbar support and SaddleHyde™ sides •LS seat features lattice stitch retro styling •Tuck-n’-roll (TR) seat features true tuck-n’-roll craftsmanship PART # DESCRIPTION FOR 96-98 FXD (EXCEPT FXDWG) 0803-0767 LS PART # DESCRIPTION FOR 96-98 FXD (EXCEPT FXDWG) (CONT) 0803-0768 TR THRASHIN’® PRO SERIES SEATS • Saddlemen® is proud to partner with the Thrashin’® crew on this line of performance-driven seats •Low profile and contoured for comfort •TR seat showcases true tuck-n’-roll construction •Combines a GelCore™ interior and Ultra-Foam to create a foam that is a perfect balance of rigidity and user compliance PART # DESCRIPTION FOR 96-98 FXD (EXCEPT FXDWG) 0803-0769 Smooth PART # DESCRIPTION FOR 96-98 FXD (EXCEPT FXDWG) (CONT) 0803-0770 TR •3/16”ABS thermoformed seat base for a perfect fit, with a carpeted bottom and rubber bumpers to protect paint •Includes all mounting hardware •Made in the U.S.A. 0803-0766 0803-0765 •Features GelCore™ technology that reduces engine vibration by up to 50% and road impacts by up to 92% for a noticeably comfortable ride • Driver portion dimensions: 13” L x 11”W • Lumbar section dimensions: 7” H • Passenger portion dimensions: 12” L x 7.5”W 0803-0767 0803-0768 •Ultra-Foam’s unique molding process creates an element-resistant self-skinning process that seals the foam and enhances the seat’s durability •Feature whisper Saddlehyde™ fabric •Made in the U.S.A. 0803-0770 0803-0769
BLUE part numbers are new for 2026 PARTS-UNLIMITED.COM 2026-2027 | OLDBOOK UPDATE EXHAUST, FUEL/AIR SYSTEMS, ENGINE FUEL/AIR SYSTEMS EXHAUST ENGINE SECTION 5 OLDBOOK DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 3-5 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. 12 RAIN SOCK FOR VO2 FALCON XL AIR INTAKE KITS • Fits all VO2 Falcon XL Air Intakes •Helps prevent moisture from reaching filter element •Custom tailored •Water repellent woven mesh fabric •Deflects debris particles as small as 0.005” • Solid black with printed Vance & Hines logo PART # DESCRIPTION 1011-5116 Rain sock for VO2 Falcon XL air intake kits ASSAULT 2-INTO-1 EXHAUST SYSTEMS • Made from high-quality stainless steel, mandrel bent, then TIG-welded •Includes custom heat shields with wire tied fasteners for race-inspired look •Double slip fit and gusset for additional strength •Made in the U.S.A. •See page 318 of the 2026-2027 Drag Specialties OldBook for the complete line of Trask Assault 2-into-1 exhaust systems PART # DESCRIPTION EMIS* FOR 99-00 FXR 1800-2806 Black/black 3 PART # DESCRIPTION EMIS* FOR 99-00 FXR (CONT) 1800-2807 Polished 3 FOR FXR 2-INTO-2 1800-2806 1800-2807
BLUE part numbers are new for 2026 EXHAUST, FUEL/AIR SYSTEMS, ENGINE DRAGSPECIALTIES.COM OLDBOOK UPDATE | 2026-2027 FUEL/AIR SYSTEMS EXHAUST ENGINE SECTION 5 OLDBOOK DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 3-5 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. 13 SLIM BA AIR CLEANER KITS •Slimmer cage to give riders more right side leg clearance, a comfort feature especially on Dyna and FXR models • Slim BA air cleaner cage is 2.375” H •With years of experience designing improved cylinder heads, combustion chambers and intake manifolds, Feuling® brings light to a new bolt-on air cleaner • Developed and designed on the flow bench, and dyno-tested •Impressive horsepower and torque gains on any engine and exceptional gains seen on engines running modified and/or ported cylinder heads along with intakes and larger throttle bodies • One piece design, creates a clean look and eases installation when compared to the industry standard multi stack up construction •Feature lengthened intake runners for increased air velocity, delivering added volume for balanced dynamic flow PART # DESCRIPTION EMIS* SOLID OUTER COVERS 1010-3444 Chrome finish w/ black filter 3 1010-3431 Chrome finish w/ red filter 3 1010-3441 Black anodized finish w/ black filter 3 1010-3429 Black anodized finish w/ red filter 3 CLEAR OUTER COVERS 1010-3445 Chrome finish w/ black filter 3 PART # DESCRIPTION EMIS* CLEAR OUTER COVERS (CONT) 1010-3432 Chrome finish w/ red filter 3 1010-3443 Black anodized finish w/ black filter 3 1010-3430 Black anodized finish w/ red filter 3 REPL. COMPONENTS 1011-5111 Repl. black slim air filter element N/A 1011-5110 Repl. red slim air filter element N/A MANGANESE BRONZE VALVE GUIDE KITS •Precision-machined guides • Excellent heat conductivity, which promotes long valve life •Guides can be easily reamed with a battery-operated or electric drill and finished with a high-quality ball hone •Eliminates the need for expensive honing equipment that would be required for nickel bronze valve guides • Kits include two intake guides, two exhaust guides and four high quality valve guide seals •Made in the U.S.A. •See page 411 of the 2026-2027 Drag Specialties OldBook for additional Manganese bronze valve guides SIZE PART # GUIDE OD GUIDE ID FOR 84-99 EVOLUTION Std. 0926-34601 0.5625” 0.3075” +0.001” 0926-34611 0.5635” 0.3075” SIZE PART # GUIDE OD GUIDE ID FOR 84-99 EVOLUTION (CONT) Std. 0926-34622 0.5620” 0.3098” +0.001” 0926-34632 0.5630” 0.3098” 1 0.530” seal diameter. Shortened for 0.655” lift for 5/16” stem valves. 2 0.420” seal diameter. Shortened for 0.600” lift. 0926-3460 FOR 93-99 EVOLUTION BIG TWIN W/ CV CARB •High flow billet aluminum velocity stack with optimal opening diameter, outer lip and internal (ID) taper • High flow washable/reusable 1.775” H air filter with one-piece billet cage •Available with solid or clear outer covers •Optional external race only breather kit PART #1012-0263 allows the air cleaners to be converted from standard intake breathing to external breathers (sold separately on page 692 of the 2026 Drag Specialties FatBook) •Made in the U.S.A. NOTE: Fit 93-99 Evolution Big Twin models (head breather, 1/2”-13 breather bolts). Only compatible with H-D CV carburetors or Mikuni HSR42/45 with CV airbox adapter.Will not fit 86-earlier Keihin Butterfly carburetors or S&S carburetors. 1010-3430 1010-3432 1010-3441 1010-3444
BLUE part numbers are new for 2026 PARTS-UNLIMITED.COM 2026-2027 | OLDBOOK UPDATE TRANSMISSION & DRIVELINE TRANSMISSION & DRIVELINE SECTION 8 OLDBOOK 14 COMPENSATOR SPRING •Performance compensator replacement spring • Thicker, stronger and an increased bevel over stock •Features a steeper bevel that provides more preload and pressure on the spring pack and compensator •This helps diminish excessive compensator travel in turn reducing harmonics, eases start up and gives a more responsive feel at lower engine rpm’s • Replaces the first, outer most spring in compensator spring pack OEM #s 40384-83, 40267-85, 40384-91, 40356-06, 40356-07 •Made in U.S.A. NOTE: Feuling® spring is not a fix for excessively worn and/or damaged compensators. PART # DESCRIPTION 1120-0471 For 84-99 Evolution Big Twin SCORPION CLUTCH PLATE SET •Kits include aramid friction and steel plates •Made in the U.S.A. •See page 507 of the 2026-2027 Drag Specialties OldBook for Barnett’s full line of Scorpion billet clutches and replacement clutch plate sets PART # DESCRIPTION 1131-4051 For 90-97 Big Twin w/ Scorpion billet clutch PART #s DS223721, 1130-0231 REAPER ADJUSTABLE SHIFT ROD • Fits most forward-controls on Dyna, Softail, and Touring models •Textured black finish •Precision CNC-machined billet aluminum • Adjustable from 12” to 13” •Replaces stock H-D shift rod PART # DESCRIPTION 1601-0611 Reaper adjustable shift rod PRIMARY CHAINS •Designed to handle stock to high-horsepower/torque applications •Precision engineered and heat-treated components reduce chain stretch and extend operation life •Approximately 11% stronger than the stock primary chain •Direct OEM replacement PART # SIZE DESCRIPTION 1120-0470 428-2 x 76 For 80-98 FLT/FXR/FXRS/FXRT (5-speed); repl. OEM #40037-79A 1120-0467 428-2 x 82 For 84-99 FXST/FLST, 91-98 Dyna and 36-86 Big Twin (4-speed); repl. OEM #s 40007-36A, 40007-36B 1120-0470
BLUE part numbers are new for 2026 ELECTRICAL DRAGSPECIALTIES.COM OLDBOOK UPDATE | 2026-2027 ELECTRICAL SECTION 10 OLDBOOK DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 3-5 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. 15 STATOR •Direct replacement to your original unit • Plug-and-play, direct fit, easy installation • Highest grade copper windings, resistant to 392 °F • Includes: pulsar coil, connector and rubber grommet PART # DESCRIPTION 2112-1993 For 84-87 FLT/FLHT, 84-88 FXST/FLST, 85-86 FXWG, 84-87 FXR, 81-84 Shovelhead; repl. OEM #29965-81/A ALTERNATOR ROTORS •Built to OEM size; fits precisely in your ride •Improved epoxy; uses high temperature epoxy that is stronger than OEM, eliminating the possibility of magnet detachment •High grade steel capping prevents harsh additives in motor oil from degrading the epoxy attaching the magnets •Precise balancing eliminates crankshaft vibrations for longer engine longevity PART # DESCRIPTION 2112-2020 For 95-96 FLHTCUI/FLHTCI/FLHRI; repl. OEM #29981-95 2112-2021 For 84-96 FLT/FLHT/FLHR (except FLHTCUI/FLHTCI/FLHRI); repl. OEM #29957-81B PART # DESCRIPTION 2112-2021 For 84-96 FXST/FLST, 91-96 FXD/FXDWG, 85-86 FXWG, 88-94 FXR; repl. OEM #29957-81B 2112-2021 For L81-84 Shovelhead; repl. OEM #29957-81B VOLTAGE REGULATORS •Machined billet aluminum casing which dissipate heat 33% better than standard molded casing • Lowers regulator and stator temperatures, more accurate voltage regulation, and increased reliability of your charging system components •50A rating PART # DESCRIPTION 2112-2012 For 91-99 FXST/FLST 2112-2012 For 91-98 FXD/FXDWG PART # DESCRIPTION 2120-1491 Universal voltage regulator 2120-1479 Universal volltage regulator (rectifier) 2112-2020 2112-2012 FLYWHEEL PULLER • Flywheel pullers for ATV/UTV, offroad and street bikes PART # DESCRIPTION 3801-0460 Flywheel puller
BLUE part numbers are new for 2026 PARTS-UNLIMITED.COM 2026-2027 | OLDBOOK UPDATE ELECTRICAL ELECTRICAL SECTION 10 OLDBOOK DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 3-5 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. 16 SLA MAX BGZ FACTORY-ACTIVATED AGM MAINTENANCE-FREE BATTERIES •Provide maximum reliability and highest starting ability to all heavy-duty engines •Designed with taller plates and built-in copper nuts terminals •Superior capacity •AGM construction (Absorbed Glass Material) •VRLA battery (Valve Regulated Lead Acid) •Sealed and factory activated •Spillproof design •Multi-positional fitment •Ready and easy to use •Increased power and extended life •Extreme vibration resistance •See page 629 of the 2026-2027 Drag Specialties OldBook for the entire line of BS Battery SLA MAX BGZ Factory-Activated batteries NOTE: Factory-Activated batteries should be charged once a month when not in service. PART # DESCRIPTION 2113-0987 For 91-99 FXST/FLST, 91-98 Dyna PART # DESCRIPTION 2113-0986 For 84-90 FXST, 86-90 FLST, 85 FXE PART # YUASA REF. # CAPACITY AH (10-HR) CAPACITY AH (20-HR) CCA @ 0 °F LENGTH WIDTH HEIGHT APPROX. WEIGHT (LBS.) TERMINAL CONFIGURATION 2113-0986 GYZ20H 20 21.1 320 6.9” 3.5” 6.1” 15.3 + - 2113-0987 GYZ20HL 20 21.1 320 6.9” 3.5” 6.1” 15.3 - + 2113-0987 PART # DESCRIPTION 3801-0487 Digital multimeter tester DIGITAL MULTIMETER DC/AC OLTAGE RESISTANCE DIODE TRANSISTOR CONTINUITY TESTER •Portable 3 1/2” digital multimeter • Measures DC and AC voltage, DC current, resistance, diode, transistor, with an audible continuity test •3 batteries included (AAA) •2 fuses included •Made with the highest quality materials •Very high degree of accuracy
BLUE part numbers are new for 2026 LIGHTING DRAGSPECIALTIES.COM OLDBOOK UPDATE | 2026-2027 LIGHTING SECTION 11 OLDBOOK 17 5 3/4” HEADLIGHT HOUSINGS •Screw-in bezel with locking feature •Spun billet aluminum housing •Fully machined with mirrored finish •For custom chopper applications; fits on 3/4” block using 3/8” diameter bolts (sold separately) •Fits all SAE 3/4” lamps (sold separately) • Includes 6” pigtail •Made in the U.S.A. NOTE: No bulb or glass included. PART # DESCRIPTION FOR 87-94 FXLR, 84-99 FXST, 98-99 FXSTB, 86-99 FXSTC, 93-98 FXDWG 2001-3061 Bradley Concours Rocket, gloss black (6” diameter, 7 3/4” L,“Spikey” visor) 2001-3060 Mariah Rocket, chrome (6” diameter, 7 3/4” L, traditional rounded visor) PART # DESCRIPTION FOR 87-94 FXLR, 84-99 FXST, 98-99 FXSTB, 86-99 FXSTC, 93-98 FXDWG (CONT) 2001-3062 Mariah Concours Rocket, gloss black (6” diameter, 8 3/4” L,“Spikey” visor) 2001-3063 Vampire Concours Rocket, chrome (6” diameter, 8 3/4” L,“Spikey” visor) 4 1/2” HEADLIGHT HOUSING •Screw-in bezel with locking feature •Spun billet aluminum housing •Fully machined with mirrored finish •For custom chopper applications; fits on 3/4” block using 3/8” diameter bolts (sold separately) •Fits all SAE 3/4” lamps (sold separately) • Includes 6” pigtail •Made in the U.S.A. NOTE: No bulb or glass included. PART # DESCRIPTION 2001-3065 Bradley Concours Rocket, chrome (4 5/8” diameter, 4 5/8” L, traditional flat front visor) 2001-3066 Bradley Concours Rocket, gloss black (4 5/8” diameter, 4 5/8” L, traditional flat front visor) 2001-3064 Bradley Concours Rocket, gloss black (4 5/8” diameter, 6 5/8” L, traditional flat front visor) 2001-3069 Mariah Concours Rocket, chrome (4 5/8” diameter, 7 3/8” L, traditional round visor) 2001-3070 Mariah Concours Rocket, gloss black (4 5/8” diameter, 7 3/8” L, traditional round visor) 2001-3067 Vampire Concours Bullet, chrome (4 5/8” diameter, 5 3/8” L,“Spikey” pointed Vampire visor) 2001-3068 Vampire Concours Bullet, gloss black (4 5/8” diameter, 5 3/8” L,“Spikey” pointed Vampire visor) 2001-3071 Vampire Concours Rocket, gloss black (4 5/8” diameter, 7 3/8” L,“Spikey” pointed Vampire visor) 2001-3063 2001-3062 2001-3061 2001-3071 2001-3070 2001-3065
BLUE part numbers are new for 2026 PARTS-UNLIMITED.COM 2026-2027 | OLDBOOK UPDATE LIGHTING LIGHTING SECTION 11 OLDBOOK 18 HEADLIGHT MOUNTS • Made from 6061 T-6 billet aluminum •Come in chrome or black finish PART # WORKS W/ HEADLIGHT STYLE COLOR BASE (L X W OR DIA.) OFFSET FOR CUSTOM MOUNTING W/ SPRINGER FORK FRONT ENDS 2001-3113 Bullet Chrome 1 1/2” x 3/4” 3/4” forward, 5/8” up FOR 80-86 FXWG, 84-99 FXST, 86-99 FXSTC, 87-94 FXLR, 93-98 FXDWG, 98-99 FXSTB 2001-3114 Bullet/Rocket Chrome 3/4” x 3/4” 1” forward, 1 9/32” up 2001-3115 Bullet/Rocket Black 3/4” x 3/4” 1” forward, 1 9/32” up 2001-3121 Bullet Chrome 3/4” diameter 7/8” up 2001-3122 Bullet Black 3/4” diameter 7/8” up 2001-3123 Bullet Chrome 3/4” diameter 1 5/8” up 2001-3124 Bullet Black 3/4” diameter 1 5/8” up 2001-3112 Bullet Black 1 1/4” diameter 7/8” up 2001-3125 Bullet Chrome 1 1/4” diameter 1 1/4” up 2001-3126 Bullet Black 1 1/4” diameter 1 1/4” up 2001-31312 Bullet Chrome 1 1/4” diameter 1 3/8” up 2001-3120 Rocket Black 1” x 3/4” 1 5/8” forward, 7/16” down FOR 82-99 FXR, 95-98 FXD 2001-3127 Universal Chrome 7/8” x 3/4” 7/8” forward, 2 1/4” up 2001-3128 Universal Black 7/8” x 3/4” 7/8” forward, 2 1/4” up 2001-3129 Universal Chrome 1 1/4” x 3/4” 1 3/8” up 2001-3130 Universal Black 1 1/4” x 3/4” 1 3/8” up FOR 88-99 FXSTS, 97-99 FLSTS 2001-31181 Bullet Black 1/2” x 3/4” 1 1/4” forward 2001-3116 Rocket Chrome 3/4” x 3/4” 2 1/8” forward 2001-3117 Rocket Black 3/4” x 3/4” 2 1/8” forward 1 Does not work with FLSTS. 2 For aftermarket trees. SHARK DEMON® HIGH PERFORMANCE LED FOG LIGHTS •Aggressive industrial styling compliments Shark Demon® headlights with signature fins and exposed screws for a bold mechanical look •Gloss black aluminum housing combines lightweight strength with a sleek, high-end finish •Durable polycarbonate lens provides impact and scratch-resistance for maximum protection in rugged riding environments • 4140 raw lumens, 2080 effective lumens per pair • Daylight white clear lens: 5800 to 6500K; crisp, ultra-bright white light for enhanced detail and maximum visibility • Selective yellow lens: 2900 to 3100K; cuts through fog, rain and snow by minimizing glare and boosts contrast PART # DESCRIPTION FOR 94-98 FLHR/FLHRC/FLHTC/FLHTCU, 98 FLTR, 94-96 FLTCU, 95-98 FLHT 2001-3091 Clear 2001-3092 Yellow PART # DESCRIPTION UNIVERSAL; FOR 12VDC SYSTEMS 2001-3097 Clear 2001-3098 Yellow P-CLAMP FOG LIGHT MOUNTS • Designed for secure, stylish mounting of both Shark Demon® and ProBEAM® fog lights (sold separately) •Installs easily on your engine guards with included Allen wrench • Engineered with a 1.25” inside diameter to seamlessly wrap around most standard motorcycle engine guards DESCRIPTION PART # Chrome 2001-3100 DESCRIPTION PART # Gloss black 2001-3099 2001-3099 2001-3100 •Adjustable beam directs light exactly where you need it with flexible vertical or horizontal mounting •Includes pair of fog light assemblies and plug-and-play wiring harness •Waterproof to IP67 •SAE/ECE compliant 2001-3113 2001-3126 2001-3129 2001-3092 2001-3097 2001-3117 2001-3131
BLUE part numbers are new for 2026 LIGHTING DRAGSPECIALTIES.COM OLDBOOK UPDATE | 2026-2027 LIGHTING SECTION 11 OLDBOOK 19 REAPER FRONT AMBER LED TURN SIGNALS •Replaces stock H-D turn signals •Precision CNC machined billet aluminum •Gloss black finish •Single function turn signal light only •Front signals use solid 5/16” bolt, lighting controller or load equalizer may be required •Sold in pairs PART # DESCRIPTION 2020-2425 Reaper front amber turn signals MICRO BULLET V2 REAR LED TURN SIGNALS •Aluminum bullet shaped housing with sealed acrylic spherical lens maximizes LED light output for a bright spot of light •Three-wire units function as red running light with full contrast amber turn signal, no additional converters required • 45” leads are pre-pinned for use with optional wire harnesses available for plug-and-play installation (sold separately) •Wiring can also be hardwired for custom applications •22ga wire •Mounting hardware included •For 12VDC systems •Sold in pairs PART # DESCRIPTION 2040-3477 Micro Bullet V2 rear LED turn signals TURN SIGNAL CLAMPS •For H-D models with 43 mm forks •Clamps have a 2 11/16” outer diameter (OD) •Include 5/16”-24 x 1/2” hex head cap screws •Fits any turn signal with 5/16”-24 threads •Sold in pairs PART # DESCRIPTION 2001-3136 Chrome PART # DESCRIPTION 2001-3137 Black DUAL ACCESSORY ADAPTER •Converts the stock H-D A connector into a dual accessory port to run two accessories from a single connection •Allows you to keep the original wiring harness intact with no splicing, cutting or other permanent changes •Plug-and-play installation into existing A connector; no modification required PART # DESCRIPTION 2120-1495 For 94-95 FLHTC, 94-97 FLHTCU, 95-98 FLHTCUI, 96 FLTCUI, 94-98 FLHR/FLHRI/FLHRC, 96-98 FLHTCI, 98 FLTRI/FLTR 2001-3136 2001-3137
BLUE part numbers are new for 2026 PARTS-UNLIMITED.COM 2026-2027 | OLDBOOK UPDATE LIGHTING LIGHTING SECTION 11 OLDBOOK 20 PART # DESCRIPTION LIGHTING KITS 2040-3488 Engine lighting kit, for any model w/ 12V power source 2040-34861 Lighting expansion kit 2120-1514 Universal Brake and turn signal adapter kit; for 12V electrical systems w/ turn and/or brake lighting circuits ACCESSORIES 2120-1513 Dead end plugs (5 pk.) 2040-34891 3” LED pods (pr.) 2040-34901 12” LED strips (pr.) PART # DESCRIPTION ACCESSORIES (CONT) 2050-05901 Shock & Awe EVOLVED™ controller (ea.) 2120-1510 8” wire extensions (pr.) 2120-1511 22” wire extensions (pr.) 2120-1512 30” wire extensions (pr.) 2120-1515 48” wire extensions (pr.) 2120-1509 6-pin Y-splitter (pr.) 1 Requires Shock & Awe EVOLVED controller PART #2050-0590 or Engine Lighting kit PART #2040-3488 (sold separately). SHOCK & AWE EVOLVED™ ENGINE LIGHTING KITS •Engine kit is the ultimate accent and underglow lighting kit • Features multiple chase, constant, breathe, flash and work light animations •Power-on and start-up animations as well as color palette, race mode, speed animation and music modes •Preloaded animations that are customizable; create, save and load your own custom color sequences •Control lighting with free Bluetooth® app called Ciro® Central Hub or included manual controller •Twice as bright as previous version •Brake and turn signal integration with added animations (harness sold separatley) •Four channels for different lighting zones •Assign individual functions to individual light pods or groups of lights •Last active lighting function saved when turned off •Expandable up to 64 light pods to illuminate any part of your motorcycle • Water resistant, low profile light pods and connectors •Pre-applied 3M™ VHB™ adhesive •Low battery voltage shutoff • Fork illuminator kit includes half-moon shaped, stamped steel illuminators to maximize light spread on front wheel • Lighting expansion kit includes two 12” light strips, two 30” wire extensions, one Y-splitter, two 48” wire extension and two dead end plugs •Universal brake and turn signal adapter kit adds brake and turn signal functions Shock & Awe EVOLVED™ lighting kits 2120-1514 2050-0590 2040-3486 2040-3488 2040-3489 2040-3490 2120-1513
BLUE part numbers are new for 2026 HANDLEBARS, CONTROLS & MIRRORS DRAGSPECIALTIES.COM OLDBOOK UPDATE | 2026-2027 SECTION 12 OLDBOOK 21 MONZA BCS MODULAR HANDLEBAR CLAMPS •Featuring a lightweight trestle skeletal style design •Handlebar degree indicators •All ARP hardware including riser bolts •1/4”-20 threaded accessory and gauge mounting options PART # DESCRIPTION 0603-1173 Black PART # DESCRIPTION 0603-1172 Raw 1 1/8” HANDLEBAR RISER KITS •Made from 6061-T6 aluminum •3 1/2” center-to-center riser spacing •1 1/8” diameter clamping area •Top clamp and hardware included •Pullback risers feature 1 1/2” of pullback •Made in the U.S.A. PART # RISE DESCRIPTION STRAIGHT 0602-1535 6” Black 0602-1536 6” Raw 0602-1537 8” Black 0602-1538 8” Raw 0602-1539 10” Black 0602-1540 10” Raw PART # RISE DESCRIPTION PULLBACK 0602-1541 6” Black 0602-1542 6” Raw 0602-1543 8” Black 0602-1544 8” Raw 0602-1545 10” Black 0602-1546 10” Raw 1” HANDLEBAR RISER KITS •Made from 6061-T6 aluminum •3 1/2” center-to-center riser spacing •Top clamp and hardware included •Pullback risers feature 1 1/2” of pullback •Made in the U.S.A. PART # RISE DESCRIPTION STRAIGHT 0602-1523 6” Black 0602-1524 6” Raw 0602-1525 8” Black 0602-1526 8” Raw 0602-1527 10” Black 0602-1528 10” Raw PART # RISE DESCRIPTION PULLBACK 0602-1529 6” Black 0602-1530 6” Raw 0602-1531 8” Black 0602-1532 8” Raw 0602-1533 10” Black 0602-1534 10” Raw 0603-1172 0602-1535 0602-1544 0602-1523 0602-1534
BLUE part numbers are new for 2026 PARTS-UNLIMITED.COM 2026-2027 | OLDBOOK UPDATE HANDLEBARS, CONTROLS & MIRRORS SECTION 12 OLDBOOK 22 GHOST RISERS AND TOP CLAMP KITS •CNC machined from 6061 Aluminum for strength, precise fitment and cosmetic accuracy •Polished chrome-plated and black anodized finishes available to match color and appearance of handlebars •1 1/2” of pullback for comfortable riding posture • 8” and 10” heights to accommodate end rise preference • Accepts 1” or 1 1/4” diameter handlebars PART # DESCRIPTION 1” DIAMETER CLAMP AREA 0602-1618 8” risers w/ standard clamp, chrome 0602-1622 8” risers w/ standard clamp, black anodized 0602-1619 10” risers w/ standard clamp, chrome 0602-1623 10” risers w/ standard clamp, black anodized PART # DESCRIPTION 1 1/4” DIAMETER CLAMP AREA 0602-1624 8” risers w/ standard clamp, chrome 0602-1625 8” risers w/ standard clamp, black anodized METHOD LEVER SET •Feature a performance inspired design with an ergonomic shape and short length •Each lever is shaped to enhance the feel and comfort of the hand controls •Backside of each lever is cut out for reduced weight, then polished for a sculpted, smooth finish PART # DESCRIPTION 0610-2489 For 96-99 Evolution Big Twin w/ cable-operated clutch HAWK GRIPS •Ergonomic design for comfort that mounts seamlessly to stock controls •Precision CNC machined aluminum •Black machined or textured black finish •Rubber grip sleeves • Fit 1” diameter handlebars •Sold in pairs PART # DESCRIPTION FOR 82-99 BIG TWIN (EXCEPT MODELS W/ AIR-ASSISTED FORKS) AND 82-85 XL 0630-3542 Black machined 0630-3543 Black textured REAPER GRIPS •Ergonomic design for comfort that mounts seamlessly to stock controls •Precision CNC machined aluminum •Textured black finish •Rubber grip sleeves • Fit 1” diameter handlebars •Sold in pairs PART # DESCRIPTION 0630-3546 For 82-99 Big Twin (except models w/ air-assisted forks) and 82-85 XL ASCENT PRO MIRRORS • Elevate your bar setup with the clean, aggressive design of the Kodlin Ascent Pro Mirrors • Featuring signature Ascent Pro machining details, these mirrors combine premium aesthetics with exceptional performance •Precision-forged mirror head and stem from billet aluminum •Heavy-duty proprietary internal pivot system crafted from stainless steel •Ultra-slim mirror profile delivers outstanding rear visibility • Available in chrome, gloss black and matte black finishes • Dimensions: 4.65” x 2.4” head, stem height 5.2” PART # DESCRIPTION LEFT 0640-1857 Chrome 0640-1858 Gloss black PART # DESCRIPTION LEFT (CONT) 0640-1856 Matte black PART # DESCRIPTION RIGHT 0640-1860 Chrome 0640-1861 Gloss black PART # DESCRIPTION RIGHT (CONT) 0640-1859 Matte black •Fits models without a Batwing fairing and a standard 3 1/2” on-center riser mounts •Matching hardware included 0602-1623 0602-1625 0602-1618 0630-3542 •Universal H-D fitment •Perfectly complement the rest of the Kodlin Ascent Pro lineup as well as other Kodlin covers •Sold each •CNC machined from forged billet aluminum with a red anodized finish •Sold as a set (both clutch and brake levers are included) 0640-1857 0640-1856 0640-1861 0630-3543
BLUE part numbers are new for 2026 CABLES DRAGSPECIALTIES.COM OLDBOOK UPDATE | 2026-2027 SECTION 13 OLDBOOK BRAIDED HIGH EFFICIENCY CLUTCH CABLES •The Industry’s highest quality braid available in four color choices to complement your bike; Sterling Chromite®, Black Pearl, KarbonFibr and Polished Stainless •Braid color and weave match on all Magnum control cables and brake lines •New chrome adjuster with integrated cover contains water-resistant seals for the best in appearance and performance • Coated with a non-yellowing, crystal-clear outer jacket for exceptional protection against scuffing paint or chrome • Low-effort, high-efficiency cable design meets or exceeds all OE specifications for fitment, construction and endurance •All fittings are polished and chrome or black chrome-plated •Rubber seal in transmission fitting eliminates fluid leaks • Cables are made with anti-friction inner liners and adjuster inserts, plus they are factory lubricated for smooth, consistent, long lasting operation •Assembled in the U.S.A. •See pages 900-901 of the 2026-2027 Drag Specialties OldBook for the entire line of Magnum Braided High Efficiency clutch cables NOTE: Check torque spec on transmission fitting when installing. HOW TO MEASURE CLUTCH CABLES NOTE: Cables are measured with the adjuster completely collapsed.Travel is measured with cable straight. 23 BRAIDED HIGH EFFICIENCY CLUTCH CABLES continued on next page. FITS MODEL STERLING CHROMITE® BLACK PEARL KARBONFIBR POLISHED STAINLESS HOUSING LENGTH ADJUSTER LOCATION FROM TRANS TRAVEL OEM # DRESSER (5-SPEED) For 87 FLHT 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 87-88 FLHTC 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 87-88 FLHTCU 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 87-88 FLHS 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 87-88 FLTC 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A STANDARD LENGTH HIGH EFFICIENCY CLUTCH CABLES Black Pearl Polished Stainless KarbonFibr Sterling Chromite®
BLUE part numbers are new for 2026 PARTS-UNLIMITED.COM 2026-2027 | OLDBOOK UPDATE CABLES SECTION 13 OLDBOOK BRAIDED HIGH EFFICIENCY CLUTCH CABLES (CONT) 24 STERLING CHROMITE® BLACK PEARL KARBONFIBR POLISHED STAINLESS HOUSING LENGTH ADJUSTER LOCATION FROM TRANS TRAVEL FOR 89-98 DRESSER 0652-3271 0652-3303 - 0652-3326 52 3/4” 23 9/16” 2 9/16” 0652-3275 - - - 61 1/4” 21 11/16” 2 9/16” 0652-3273 - - - 67 1/4” 21 11/16” 2 9/16” 0652-3274 - - - 69 1/4” 21 11/16” 2 9/16” 0652-3272 - - - 71 1/4” 21 11/16” 2 9/16” FOR 87-98 BIG TWIN (EXCEPT 87-89 DRESSER) 0652-3289 - - - 57 11/16” 32 15/16” 2 13/16” 0652-3286 - - - 59 11/16” 32 15/16” 2 13/16” 0652-3287 - - - 61 11/16” 32 15/16” 2 13/16” 0652-3288 - - - 63 11/16” 32 15/16” 2 13/16” 0652-3282 0652-3309 - - 66 11/16” 32 15/16” 2 13/16” 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 0652-3269 - - - 65 11/16” 32 15/16” 2 13/16” 0652-3285 0652-3312 - 0652-3333 64 7/16” 32 15/16” 2 13/16” 0652-3283 - - - 67 11/16” 32 15/16” 2 13/16” 0652-3284 0652-3311 - 0652-3332 70 11/16” 32 15/16” 2 13/16” 0652-3281 0652-3308 0652-3418 0652-3331 68 11/16” 32 15/16” 2 13/16” 0652-3277 - - - 71 11/16” 32 15/16” 2 13/16” 0652-3278 0652-3305 - 0652-3328 72 11/16” 32 15/16” 2 13/16” 0652-3279 0652-3306 0652-3417 0652-3329 74 11/16” 32 15/16” 2 13/16” 0652-3280 0652-3307 - 0652-3330 76 11/16” 32 15/16” 2 13/16” 0652-3276 0652-3304 - 0652-3327 78 11/16” 32 15/16” 2 13/16” ALTERNATIVE LENGTH HIGH EFFICIENCY CLUTCH CABLES FOR CUSTOM HEIGHT/WIDTH HANDLEBARS STANDARD LENGTH HIGH EFFICIENCY CLUTCH CABLES (CONT) FITS MODEL STERLING CHROMITE® BLACK PEARL KARBONFIBR POLISHED STAINLESS HOUSING LENGTH ADJUSTER LOCATION FROM TRANS TRAVEL OEM # SOFTAIL For 99 FXST 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 87-90 FXST 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 87-99 FXSTC 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 99 FXSTB/I 0652-3289 - - - 57 11/16” 32 15/16” 2 13/16” 38665-00 For 87-99 FLSTC 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 90-99 FLSTF 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 93-96 FLSTN 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 87-99 FXSTS 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 95-97 FXSTSB - 0652-3310 - - 60 11/16” 32 15/16” 2 13/16” 38617-95 For 87-90 FLST 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A For 97-99 FLSTS 0652-3270 0652-3302 - 0652-3325 62 11/16” 32 15/16” 2 13/16” 38607-87A DYNA For 95-98 FXD 0652-3281 0652-3308 0652-3418 0652-3331 68 11/16” 32 15/16” 2 13/16” 38602-92 For 92 FXDC 0652-3281 0652-3308 0652-3418 0652-3331 68 11/16” 32 15/16” 2 13/16” 38602-92 For 93-98 FXDL 0652-3281 0652-3308 0652-3418 0652-3331 68 11/16” 32 15/16” 2 13/16” 38602-92 For 92 FXDB 0652-3281 0652-3308 0652-3418 0652-3331 68 11/16” 32 15/16” 2 13/16” 38602-92 For 93-98 FXDWG 0652-3281 0652-3308 0652-3418 0652-3331 68 11/16” 32 15/16” 2 13/16” 38661-00 For 94-98 FXDS CONV. 0652-3281 0652-3308 0652-3418 0652-3331 68 11/16” 32 15/16” 2 13/16” 38602-92
www.parts-unlimited.comRkJQdWJsaXNoZXIy OTcxOTk3