BOLD MAGENTA part numbers are new for 2026 PARTS-UNLIMITED.COM 2026 | ATV/UTV FUEL/AIR SYSTEMS FUEL/AIR SYSTEMS 1364 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. DESCRIPTION PART # PLAIN – FUEL 3/16” ID x 25’ L 0706-0013 1/4” ID x 25’ L 0706-0014 5/16” ID x 25’ L 0706-0015 DESCRIPTION PART # REINFORCED CLEAR NYLON FUEL LINE 3/16” ID x 25’ L 0706-0227 REINFORCED – FUEL/OIL 1/4” ID x 25’ L 0711-0060 DESCRIPTION PART # REINFORCED – FUEL/OIL (CONT) 5/16” ID x 25’ L 0711-0061 3/8” ID x 25’ L 0711-0062 UNIVERSAL FUEL/OIL LINE • Universal, black fuel/oil line in 25’ rolls •Reinforced line is fuel- and oil-resistant NOTE: Do not use with fuel containing more than 10% alcohol. 0706-0013 0706-0227 0711-0060 DESCRIPTION PART # 1/4” ID 3’ L 0706-0204 25’ L 0706-0206 DESCRIPTION PART # 5/16” ID 3’ L 0706-0205 25’ L 0706-0207 LP (LOW PERMEATION) PREMIUM FUEL LINE •Certified to meet permeation emission standards of 15g/M2/day • On emission-controlled vehicles, check with local and state agencies to determine suitability •Robust multi-layer design and construction •Fluoropolymer liner compatible with higher ethanol-blend gasoline up to 100% • Highly flexible, easy to install and offers excellent fitting retention • Resistant to swelling, hardening and cracking caused by hydrocarbon-based fluids •Ozone and UV light resistant •Wide temperature range from -20 to 165 °F (-28.9 to 73.9 °C) •Yellow color for easy identification •Use Stepless® Clamps NOTE: Not for use with fuel injection systems. NOTE: On emission-controlled vehicles, check with local state agencies to determine suitability. 0706-0206 CARBURETOR FUEL LINE (NON-SUBMERSIBLE) ID PART # 2’ LENGTH 3/16” 0706-0176 ID PART # 25’ LENGTH 3/16” 0706-0180 1/4” 0706-0181 ID PART # 25’ LENGTH (CONT) 5/16” 0706-0182 3/8” 0706-0183 FUEL INJECTION FUEL LINE (NON-SUBMERSIBLE) ID PART # 25’ LENGTH 1/4” 0706-0185 ID PART # 25’ LENGTH (CONT) 5/16” 0706-0187 EXCEEDS SAE 30R10 SPECIFICATION FOR SUBMERSIBLE FUEL LINE ID PART # 1’ LENGTH 5/16” 0706-0290 ID PART # 1’ LENGTH (CONT) 3/8” 0706-0291 LP (LOW PERMEATION) FUEL LINES •Five-layer Greenshield™ barrier technology keeps fuel out of the environment, while delivering peak fuel efficiency • Heat-, oil-, ozone- and abrasion-resistant cover •Fuel-injection fuel line is recommended for all fuel-injection applications •Carburetor fuel line is not for use with pressurized fuel line applications, fuel-injection systems or cooling system applications • Fuel-injection and carburetor fuel line sold in 25’ rolls and 2’ lengths • Submersible fuel line sold in 1’ lengths •Non-submersible fuel line types meet EPA 40 CFR 1051.110 and CARB E.O. #Q-09-019 requirements for low-permeation fuel lines •Submersible fuel line types exceed SAE J30R14T1 requirements NOTE: ONLY submersible fuel line styles are suitable for in-tank use; DO NOT use fuel injection or carburetor fuel line for applications that require the fuel line be submersed in gasoline. Submersible fuel line
RkJQdWJsaXNoZXIy OTcxOTk3