BOLD MAGENTA part numbers are new for 2026 FUEL/AIR SYSTEMS PARTS-UNLIMITED.COM OFFROAD | 2026 FUEL/AIR SYSTEMS 1613 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. ID OD LENGTH OF FOAM PART # 1”/25 mm 2 3/4”/70 mm 3” UP-4112 1 1/4”/31.75 mm 2 3/4”/70 mm 3” 1011-0741 1 1/2”/38 mm 2 3/4”/70 mm 4” UP-4152 1 1/2”/38 mm 2 3/4”/70 mm 5” UP-5152 1 1/2”/38 mm 2 3/4”/70 mm 6” UP-6152 1 3/4”/44 mm 2 3/4”/70 mm 4” UP-4182 1 3/4”/44 mm 2 3/4”/70 mm 5” UP-5182 1 3/4”/44 mm 2 3/4”/70 mm 6” UP-6182 2”/50 mm 3”/76 mm 4” UP-4200 2”/50 mm 3”/76 mm 5” UP-5200 2”/50 mm 3”/76 mm 6” UP-6200 ID OD LENGTH OF FOAM PART # 2 1/4”/57 mm 3”/76 mm 4” UP-4229 2 1/4”/57 mm 3”/76 mm 5” UP-5229 2 1/4”/57 mm 3”/76 mm 6” UP-6229 2 1/2”/63 mm 3”/76 mm 4” UP-4245 2 1/2”/63 mm 3”/76 mm 5” UP-5245 2 1/2”/63 mm 3”/76 mm 6” UP-6245 2 3/4”/70 mm 3 3/4”/95.25 mm 4” UP-4275 2 3/4”/70 mm 3 3/4”/95.25 mm 5” UP-5275 2 3/4”/70 mm 3 3/4”/95.25 mm 6” UP-6275 3”/76 mm 3 3/4”/95.25 mm 4” 1011-0742 3”/76 mm 3 3/4”/95.25 mm 6” 1011-0899 POD FILTERS •Durable urethane mounting base for longer life and better fit •Seamless design for maximum airflow •Opening will reduce to 3/8” smaller than charted ID size UP-4112 1011-0899 ID ID MM LENGTH OF FOAM PART # ANGLED 1” 28 3” 1011-0754 1 1/4” 31.75 3” 1011-0755 1 1/2” 38 4” UP-4152AST 1 3/4” 44 4” UP-4182AST 1 1/2” 38 6” UP-6152AST 1 3/4” 44 6” UP-6182AST 2” 51 4” 1011-0756 2” 51 6” 1011-0761 2 1/4” 57 4” 1011-0757 2 1/4” 57 6” 1011-0762 2 1/2” 63 4” 1011-0758 ID ID MM LENGTH OF FOAM PART # ANGLED (CONT) 2 1/2” 63 6” 1011-0763 2 3/4” 70 4” 1011-0759 2 3/4” 70 6” UP-6275AST 3” 76 4” 1011-0760 3” 76 6” UP-6300AST STRAIGHT 1” 28 3” UP-4112ST 1 1/4” 31.75 3” 1011-0743 1 1/2” 38 4” 1011-0744 1 1/2” 38 6” 1011-0748 1 3/4” 44 4” 1011-0745 ID ID MM LENGTH OF FOAM PART # STRAIGHT (CONT) 1 3/4” 44 6” 1011-0749 2” 51 4” UP-4200ST 2” 51 6” UP-6200ST 2 1/4” 57 4” UP-4229ST 2 1/4” 57 6” 1011-0750 2 1/2” 63 4” UP-4245ST 2 1/2” 63 6” 1011-0751 2 3/4” 70 4” 1011-0746 2 3/4” 70 6” 1011-0752 3” 76 4” 1011-0747 3” 76 6” 1011-0753 TWO-STAGE POD FILTERS •Clamp directly to carburetor •Angled or straight design; black inner foam, red outer foam and a urethane flange • For use on motorcycles,ATVs, go-carts, snowmobiles, air compressors, tractors and anything with a carburetor •Use outside pre-filter dry for dusty conditions, oiled for extremely wet conditions 1011-0751 1011-0758 INLET ID LENGTH WIDTH PART # 28 mm 2” 2 1/4” 1011-3152 35 mm 2” 2 1/2” 1011-3153 39 mm 2 3/4” 3” 1011-3154 INLET ID LENGTH WIDTH PART # 42 mm 2 3/4” 3” 1011-3155 45 mm 3 3/4” 3 3/4” 1011-31591 46 mm 2 3/4” 3” 1011-3156 INLET ID LENGTH WIDTH PART # 48 mm 2 3/4” 3” 1011-3157 60 mm 3” 3” 1011-3158 1 With chrome half cover. CLAMP-ON POD AIR FILTERS •Quality high-flow paper elements with chrome end caps •Use included stainless steel clamp for secure attachment •Determine size or part number needed by size chart below •PART #1011-3159 has built-on chrome shell protecting 180 degrees of filter element without reducing airflow •Check carb inlet OD before ordering •Width is the largest diameter of filter media •Sold each 1011-3156 1011-3159 1011-3152
RkJQdWJsaXNoZXIy OTcxOTk3