BOLD MAGENTA part numbers are new for 2026 FUEL/AIR SYSTEMS PARTS-UNLIMITED.COM OFFROAD | 2026 FUEL/AIR SYSTEMS 1649 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. DESCRIPTION PART # Small engine fuel line variety pack 0706-0454 SMALL ENGINE FUEL LINE VARIETY PACK •Designed for small diameter fuel lines •Remains flexible and will not crack or harden when in use •Contains one each of the following sizes: 5/64”, 3/32”, and 1/8” NOTE: Not compatible with fuel containing more than 10% ethanol. DESCRIPTION PART # 1/8” ID – 3’ LENGTH Clear 0706-0138 3/16” ID X 5/16” OD – 3’ LENGTHS Black 0706-0044 Clear 0706-0041 Gray 0706-0038 1/4” ID X 7/16” OD – 3’ LENGTHS Black 0706-0045 Clear 0706-0042 DESCRIPTION PART # 1/4” ID X 7/16” OD – 3’ LENGTHS (CONT) Gray 0706-0039 5/16” ID X 1/2” OD – 3’ LENGTHS Black 0706-0046 Clear 0706-0043 Gray 0706-0040 1/8” ID – 25’ ROLL Clear 0706-0139 DESCRIPTION PART # 3/16” ID X 5/16” OD – 25’ ROLLS Black 0706-0018 Clear 0706-0021 Gray MP12-031 1/4” ID X 7/16” OD – 25’ ROLLS Black 0706-0019 Clear 0706-0022 Gray MP12-032 DESCRIPTION PART # 5/16” ID X 1/2” OD – 25’ ROLLS Black 0706-0020 Clear 0706-0023 Gray MP12-033 PREMIUM FUEL LINES •Stronger and more durable than vinyl fuel line •Use with any type of gasoline •Resists swelling and hardening • Resistant to direct sunlight, hardening and/or cracking •Flexible in temperatures from -35 to +165 °F •Fuel line stretches easily over fittings or petcocks • Sold in 3’ lengths and 25’ rolls •Made in the U.S.A. NOTE: Not for use with fuel-injected models. Black Clear Gray DESCRIPTION PART # 1/4” ID 3’ L 0706-0204 25’ L 0706-0206 DESCRIPTION PART # 5/16” ID 3’ L 0706-0205 25’ L 0706-0207 LP (LOW PERMEATION) PREMIUM FUEL LINE •Certified to meet permeation emission standards of 15g/M2/day • On emission-controlled vehicles, check with local and state agencies to determine suitability •Robust multi-layer design and construction •Fluoropolymer liner compatible with higher ethanol-blend gasoline up to 100% • Highly flexible, easy to install and offers excellent fitting retention • Resistant to swelling, hardening and cracking caused by hydrocarbon-based fluids •Ozone and UV light resistant •Wide temperature range from -20 to 165 °F (-28.9 to 73.9 °C) •Yellow color for easy identification •Use Stepless® Clamps NOTE: Not for use with fuel injection systems. NOTE: On emission-controlled vehicles, check with local state agencies to determine suitability. CARBURETOR FUEL LINE (NON-SUBMERSIBLE) ID PART # 2’ LENGTH 3/16” 0706-0176 ID PART # 25’ LENGTH 3/16” 0706-0180 1/4” 0706-0181 ID PART # 25’ LENGTH (CONT) 5/16” 0706-0182 3/8” 0706-0183 FUEL INJECTION FUEL LINE (NON-SUBMERSIBLE) ID PART # 25’ LENGTH 1/4” 0706-0185 5/16” 0706-0187 LP (LOW PERMEATION) NON-SUBMERSIBLE FUEL LINES •Five-layer Greenshield™ barrier technology keeps fuel out of the environment, while delivering peak fuel efficiency • Heat-, oil-, ozone- and abrasion-resistant cover •Fuel-injection fuel line is recommended for all fuel-injection applications •Carburetor fuel line is not for use with pressurized fuel line applications, fuel-injection systems or cooling system applications • Fuel injection sold in 25’ length; carbureted fuel line sold in 2’ or 25’ lengths • Meet EPA 40 CFR 1051.110 and CARB E.O. #Q-09-019 requirements for low-permeation fuel lines NOTE: DO NOT use fuel injection or carburetor fuel line for applications that require the fuel line be submersed in gasoline.
RkJQdWJsaXNoZXIy OTcxOTk3