ATV | UTV ACCESSORIES 2025 CAN-AM EDITION
2 www.moose-offroad.com CYLINDER ASSISTED WINDSHIELD EXPEDITION UTV CAB ENCLOSURE Windshield Details: Front windshields are made of laminated tempered safety glass. Two position tilt-out function is gas cylinder assisted. The window is attached to the overhead guard with a metal clamping system. Window locks in two positions for air intake. Wiper and washer kit sold separately. Roof Details: Constructed of 13-gauge steel, zinc coated and then powder coated to provide maximum rust protection. Noise reduction insulation is affixed on the inside of the roof as well as metal frames and supports. Rear Panel Details: Made from 5mm transparent, double UV protected, twice hardened coated polycarbonate sheet. Door Details: Made from a combination of the safety glass (sliding windows) and the transparent, double UV protected, hard coated polycarbonate with metal reinforcing structure. Both doors are lockable and fully openable. Each door is equipped with a heavy duty, key locking latch system. Comes with a pair of mirrors. Cab Heater Kit and Wiper/Washer Kits: Complete cabs do not include wiper/washer or heater kit. Sold separately. WHAT TO ORDER: If ordering a full complete cab order the appropriate number. If ordering a door set or front, top, back separate, order the appropriate number. Note: No drilling into the frame is necessary during the entire installation. WIPER/WASHER KIT COMPLETE CAB > $4,119.95 - $7,179.95 CAB HEATER > $594.95 - $759.95 WIPER/WASHER KIT > $446.95 HEATER INSTALL KIT > $125.00 SIDE ENCLOSURE > $425.95 600 denier polyester shell. Automotive grade, clear flexible acrylic side windshield w/ sewn in upper section of doors. Doors are completely removable and have full length #10 double pull zippers. Simple installation using clamps on each side attaching to roll bar for a weatherproof seal. Comes with self-adhesive hook and loop on top of doors. LOCKABLE DOORS REAR DUST PANEL > $159.95 - $179.95 Multiple straps allow the dust panel to work with most hardtops. Large vinyl window. Constructed from heavy-duty rip stop nylon. Easy installation and removal. Page 66 in the 2025 Moose Off Road ATV/UTV catalog. Page 67 in the 2025 Moose Off Road ATV/UTV catalog. Page 67 in the 2025 Moose Off Road ATV/UTV catalog . BODY
www.moose-offroad.com 3 BACK PANEL > $107.95 - $207.95 Made from .177" thick, clear polycarbonate. Adds a finished look to your UTV and keeps debris from entering the cab. Comes with all mounting hardware. Made in the USA. HALF WINDSHIELD > $158.95 - $197.95 Premium .177” thick clear polycarbonate shield. Stainless steel rubber coated mount clamps. Rubber trim at bottom of shield to help keep debris out. Made in the USA. TWO PIECE ROOF > $192.95 - $499.95 Durable polyethylene with UV stabalizers. Extremely durable in cold weather. Comes with all mounting hardware. Not for trailering. Made in the USA. FULL FOLDING WINDSHIELD > $389.95 Premium .177” thick clear polycarbonate shield. Centrally hinged for ventilation. Tool-less operation. Stainless steel rubber coated mount straps. Rubber seal helps keep elements out. Replacement kit (Part # 2317-0164) with 6" rubber seal available separately. Made in the USA. FULL FOLDING DELUXE WINDSHIELD > $375.95 Designed to work with the OEM roof whithout leaving a large gap between the top of the windshield and roof. Windshield is attached to the roll cage using four profile clamps. Middle section of the windshield is attached using three hinges with a unique fold to prevent water intrusion at the hinge line. Top folding part of the windshield is connected to the roll cage with two hook and loop straps. Made from 0.177" Polycarbonate. Made in the USA. Page 64 in the 2025 Moose Off Road ATV/UTV catalog. Page 69 in the 2025 Moose Off Road ATV/UTV catalog. Page 68 in the 2025 Moose Off Road ATV/UTV catalog. Page 70 in the 2025 Moose Off Road ATV/UTV catalog. Page 71 in the 2025 Moose Off Road ATV/UTV catalog. BODY
4 www.moose-offroad.com LOWER DOOR INSERTS > $354.95 - $373.95 Mount to existing OEM upper door. Easy fitment. No drilling necessary. Lightweight aluminum insert. Powder coated black. Come complete with all mounting hardware FOOTWELL PROTECTORS > $259.95 - $349.95 Manufactured from 4mm 5052 aluminum. Drainage and maintenance holes included. Precision laser cut and powder coated for scratch resistance. Where possible, it protects the entire footwell, brake reservoir, master cylinder and radiator overflow bottle. Sold in pairs. OVER FENDERS > $159.95 - $239.95 Sold as a complete set of 4 (2 front & 2 rear). Made of black HMW hair cell polyethylene .125”. Cut with superior CNC 5-axis router. Custom bend design for maximum rigidity. Comes complete with all mounting hardware. BENCH AND BUCKET SEAT COVER > $108.95 - $239.95 Made from 500-denier Cordura®. Protects the seat from punctures and daily wear. Comes with headrests for specific applications. Yamaha Rhino covers are made of 3.0mm black neoprene. Made in the USA. Page 74 in the 2025 Moose Off Road ATV/UTV catalog. Page 75 in the 2025 Moose Off Road ATV/UTV catalog. Page 75 in the 2025 Moose Off Road ATV/UTV catalog. Page 80 in the 2025 Moose Off Road ATV/UTV catalog. NERF BARS > $264.95 - $364.95 Extremely durable steel 1.75" tube nerf bars provide outstanding protection. In addition to the tough-looking design element, they retain the full stock ground clearance. Without hanging below the bottom of the vehicle, yet extending 5", they protect against obstacles without interfering with handling. Protects the chassis as well as the rear wheels. Mounts on the rocker panels of your UTV quickly and easily. FRONT GRILLES > $119.95 - $139.95 Aggressive and stylish. Replaces OEM plastic grill. Durable aluminum. Bolt-on design. Page 77 in the 2025 Moose Off Road ATV/UTV catalog. Page 77 in the 2025 Moose Off Road ATV/UTV catalog. BODY
www.moose-offroad.com 5 FRONT AND REAR BUMPERS > $169.95 - $259.95 ATV bumpers are made from 1 ½” tubular steel; UTV bumpers from 1 ¾” tubular steel. Bolt-on design, no drilling necessary. Multiple frame mounting points for added strength. Headlight or taillight protection. Full-coverage, heavy-duty look. Powder coated steel. Honda bumpers are gloss, Yamaha are wrinkle finish. Page 76 in the 2025 Moose Off Road ATV/UTV catalog. OEM REPLACEMENT SEAT COVERS > $43.95 - $49.95 Heavy-duty, UV resistant, black marine grade vinyl. Double stitched for durability. Must remove stock seat cover to staple on new cover. Made in the USA. SEAT FOAM > $99.95 Replace that torn up seat! OEM-style seat foam at a fraction of the cost. Uses stock base plate. Made in the USA. UTV REARVIEW/SIDEVIEW MIRROR > $19.95 Fits side or cross bar of roll cage. Wide range of adjustment. Convex mirror for wider viewing angles & image stability. Shatter resistant tempered safety glass. Page 79 in the 2025 Moose Off Road ATV/UTV catalog. Page 81 in the 2025 Moose Off Road ATV/UTV catalog. Page 90 in the 2025 Moose Off Road ATV/UTV catalog. Page 90 in the 2025 Moose Off Road ATV/UTV catalog. UTV AUTO STYLE REAR VIEW MIRRORS > $43.95 Auto styled. Highly adjustable dual ball joints. Simple 1-screw setup. Shatter resistant tempered safety glass and high impact ABS housing. Convex mirror for wider viewing angles and image stability. 1 3/4" and 2" steel bar clamp option for maximum strength and durability. Styling matches side view mirrors. ATV WINDSHIELD > $189.95 - $194.95 100” polycarbonate material. Rigid, four-point mounting hardware with breakaway design. Quick-disconnect handlebar clamps for quick, easy removal. Made in the USA. Page 71 in the 2025 Moose Off Road ATV/UTV catalog. BODY
6 www.moose-offroad.com SWINGARM SKIDPLATES > $106.95 - $134.95 Heavy-duty aluminum skidplate protects your sprocket, swingarm and brake rotor from rocks and other debris. All mounting hardware included. Made in the USA. BILLET GAS CAPS > $55.95 6061 Aluminum. Integrated rubber seal. OEM specifications. UTV CAB HEATERS > $534.95 - $619.95 12-volt universal cab heater kit for UTVs with 1" and ¾" radiator hoses. Quick and easy installation. Typically installs in about an hour. Water operated. Made in the USA. MIRROR ADAPTERS> $11.95 For use with 0640-1716 Page 85 in the 2025 Moose Off Road ATV/UTV catalog. Page 91 in the 2025 Moose Off Road ATV/UTV catalog. Page 89 in the 2025 Moose Off Road ATV/UTV catalog. Page 84 in the 2025 Moose Off Road ATV/UTV catalog. Page 83 in the 2025 Moose Off Road ATV/UTV catalog. MIRROR WITH LED DOME LIGHT> $109.95 Slightly convex mirror head increases field-of-view and gives you a truly clear view of what is behind you. Integrated vibration reducing rubberized seal and ball mount drastically reduces the buzz at all speeds. Manufactured with the highest-grade materials and designed with versatility in mind. Low-profile mount is compatible with most windshields and roofs. Integrated ball mount allows for microadjustments on-the-fly. BODY
www.moose-offroad.com 7 QUARTER TURN/QUICK RELEASE BOLTS > $19.95 Roof fastener kit. Sold as a 4-pack. CONTROL CABLES > $15.95 - $21.95 Black PVC outer jacket for maximum flexibility & durability. Steel inner casing that is tightly coiled for low compression ratios. Pre-lubricated nylon inner sleeve guarantees smooth operation and long life. All wire ends are bird caged prior to terminal casting for superior pull-out resistance. EPDM molded rubber components for high UV resistance & long life. Injected molded components are manufactured from high strength POM material. SHIFT CABLES > $54.95 - $64.95 Sticky shifting or excessive gear clash? The shift cables can wear out or break over time. This complete cable assembly will install and work just like OEM. Heavy duty stainless steel end fittings at both ends for corrosion resistance and longevity. BILLET SHIFTERS > $64.95 OEM replacement parts made with 6061 billet aluminum. 11-WAY REBUILDABLE STEERING STABILIZERS > $214.95 11-way compression adjusts soft to hard. All billet aluminum construction. End caps protect seals from dirt and mud. Adjusting knob and body clamp. Available with silver or black clamps. Made in the USA. 7-WAY STEERING STABILIZERS > $190.95 - $204.95 7-way compression adjusts soft to hard. All billet aluminum construction. End caps protect seals from dirt and mud. Adjusting knob and body clamp. Available in rebuildable and non-rebuildable. Available with silver or black clamps. Made in the USA. THROTTLE BLOCK ASSEMBLY > $39.95 - $59.95 Made from high-quality aluminum, ensuring longevity and reliability. Black anodized finish adds a touch of style and helps against wear and tear. Direct replacement and simple plug and play installation. HANDLEBAR SWITCH BLOCK> $54.95 Complete block has all the same switches including hi/lo/off beam, off/run/off, and reverse override. Simple installation. BILLET DOOR HANDLES > $99.95 Replaces the OEM door strap. Aluminum construction. Rigid, easy to grab design. Fits all models. Sold in pairs. Page 100 in the 2025 Moose Off Road ATV/UTV catalog. Page 102 in the 2025 Moose Off Road ATV/UTV catalog. Page 87 in the 2025 Moose Off Road ATV/UTV catalog. Page 87 in the 2025 Moose Off Road ATV/UTV catalog. Page 107 in the 2025 Moose Off Road ATV/UTV catalog. Page 107 in the 2025 Moose Off Road ATV/UTV catalog. Page 102 in the 2025 Moose Off Road ATV/UTV catalog. Page 94 in the 2025 Moose Off Road ATV/UTV catalog. Page 99 in the 2025 Moose Off Road ATV/UTV catalog. OEM REPLACEMENT HANDLEBARS> $41.95 Avoid paying OEM cost for replacement handlebars. Available in OEM bends. 7/8” diameter and made from .083 steel tubing. Made in the USA. Page 103 in the 2025 Moose Off Road ATV/UTV catalog. CONTROLS
8 www.moose-offroad.com IGNITION SWITCHES > $24.95 - $29.95 Exact OEM replacements. Includes mounting nut and two keys. Replaces lost keys or broken switches. Replacment key cover: 2106-0486 > $5.95 Replacment key: 2106-0487 > $7.95 SPARK PLUG CAP/WIRE > $17.95 - $35.95 Exact replacement spark plug cap and wire by the original manufacturer, it is not a reproduction. It will fit either cylinder, just twist the rubber seal to fit left or right cylinder. The 25" plug wire will simply twist into the CDI box for an easy replacement. PART #s 2104-0351 and 2104-0352 sold in pairs; all others sold each. FUEL PUMP PIGTAIL HARNESS > $25.95 Simply cut off the old plugs and use the included butt connectors or solder the connections to the new pigtail. Fits perfectly to the fuel pump and has 9" long wire leads. TAILLIGHT PIGTAIL REPAIR HARNESS KIT > $25.95 Direct replacment. T-MAP SENSORS > $39.95 A dirty or bad T-map sensor can cause rough or inconsistent idle, stalling, or just overall poor performance. Replace it now with this unit. SPARK PLUG RESISTOR COVERS > $5.95 - $7.95 Thirteen different styles available to fit most applications. Replaces NGK resistor covers. Ceramic resistors that insure performance. High quality durable phenolic resins. Waterproof caps for superior performance. Allowable plug thread sizes: 10mm, 12mm and 14mm. Allowable terminal type in a stud or nut. T-MAP SENSOR PIGTAIL HARNESS > $25.95 The wire harness to the T-map sensor is a well-known issue on Polaris EFI machines. Simply cut off the old harness and use the included butt connectors or solder the connections to the new pigtail. IGNITION KEYSWITCH PIGTAIL HARNESS > $29.95 Connectors to the ATV ignition switches are prone to corroding. Cut off the old harness and use the included butt connectors or solder the connections to the new pigtail. Fits perfect to the ignition switch with a wire sheathing protecting the wires into the plug. 6" long wires fix to the inside of the headlight pod. Sold each; includes butt connectors and zip ties. RELAYS > $17.95 - $19.95 Direct replacement relays by the original manufacturers, not reproduction units. Each relay is the exact same voltage and amperage. Used to control functions like the fuel pump, power steering, cooling fan, EFI, etc. Most machines use multiple relays and are located in the fuse box. Page 126 in the 2025 Moose Off Road ATV/UTV catalog. Page 129 in the 2025 Moose Off Road ATV/UTV catalog. Page 132 in the 2025 Moose Off Road ATV/UTV catalog. Page 128 in the 2025 Moose Off Road ATV/UTV catalog. Page 131 in the 2025 Moose Off Road ATV/UTV catalog. Page 127 in the 2025 Moose Off Road ATV/UTV catalog. Page 124 in the 2025 Moose Off Road ATV/UTV catalog. Page 128 in the 2025 Moose Off Road ATV/UTV catalog. Page 126 in the 2025 Moose Off Road ATV/UTV catalog. PLUG AND PLAY POWER PIGTAIL HARNESS > $34.95 Don’t cut your factory wire harness. Can be used with our LED whips or any 12v accessory all without cutting or damaging your factory wire harness. Page 131 in the 2025 Moose Off Road ATV/UTV catalog. 12" SHOCK TOWER LIGHT BAR MOUNT > $44.95 This heavy-duty steel mount gives you an easy place to mount your 12” light bar. Page 111 in the 2025 Moose Off Road ATV/UTV catalog. LED HEADLIGHTS/TAILLIGHTS > $19.95 - $349.95 Replace or upgrade your stock headlights with these new LED headlights and taillights. Replace a broken light with a direct replacement or upgrade your halogen lights to LED. You can even choose from a variety of options including blacked out lenses or white halo features! These lights will set your machine apart from the rest while offering super-bright LED performance. Some models require wiring adapters (sold separately). LED SIGNATURE LIGHTS > $185.95 Direct replacement clear LED accent lights, Simple direct plug and play installation. Sold as a pair. Page 114, 116 in the 2025 Moose Off Road ATV/UTV catalog. Page 115 in the 2025 Moose Off Road ATV/UTV catalog. electrical
www.moose-offroad.com 9 FACTORY-ACTIVATED AGM MAINTENANCE-FREE BATTERY > $51.95 - $146.95 Pre-filled, sealed, charged and ready to go! Spill-proof design. Sulfation retardant. Advanced lead-calcium technology. Exceptional resistance to vibration. Vast impact in extreme weather conditions. STATORS > $33.95 - $219.95 OEM style replacement stators. Designed to be complete bolt-on replacements with all connectors and grommets (unless otherwise noted). High output stators also available with additional electrical power. REGULATOR/RECTIFIERS > $33.95 - $219.95 OEM style replacement units. All regulator/rectifiers are designed as direct plug in units with all the correct connectors and terminals (unless otherwise noted). Heavy-duty parts also available that will regulate additional electrical current. STARTERS > $75.95 - $219.95 Built to OEM specifications. Direct bolt-on replacements. WHEEL HUBS > $65.95 - $85.95 Direct replacement to the OEM Hub. Replace bent or damaged hubs. Stud kit available separately. Sold as each. FRONT AND REAR WHEEL STUD AND NUT KITS > $19.95-$35.95 Kit includes components to rebuild one wheel. Includes wheel studs, nuts, washers, and other miscellaneous components. LEFT AND RIGHT WHEEL STUD AND NUT KITS > $19.95 - $35.95 Kit includes components to rebuild one wheel. Includes wheel studs, nuts, washers, and other miscellaneous components. SPARE TIRE ATTACHMENT > $162.95 Bracket anchors for simple, tool-less installation that allows for the secure mount and transport of your spare tire. Fits all wheel and tire sizes. Simple installation and removal lets you quickly carry your spare, or leave it at home. Allows for your spare tire to be stored safely and securely in the inside of the bed. Tire/wheel not included. Made in the USA. Page 136 in the 2025 Moose Off Road ATV/UTV catalog. Page 196 in the 2025 Moose Off Road ATV/UTV catalog. Page 195 in the 2025 Moose Off Road ATV/UTV catalog. Page 203 in the 2025 Moose Off Road ATV/UTV catalog. Page 204 in the 2025 Moose Off Road ATV/UTV catalog. Page 195 in the 2025 Moose Off Road ATV/UTV catalog. Page 136 in the 2025 Moose Off Road ATV/UTV catalog. Page 141 in the 2025 Moose Off Road ATV/UTV catalog. Page 144 in the 2025 Moose Off Road ATV/UTV catalog. Page 138 in the 2025 Moose Off Road ATV/UTV catalog. AGM MAINTENANCE-FREE BATTERY > $38.95 - $132.95 A heavy-duty maintenance-free 12-volt battery offering the quality you expect from Moose Utility Division® at affordable prices. Superior vibration resistance and durability provide a long service life. Holds a charge three times longer than conventional batteries. Absorbed glass mat battery eliminates water loss; permitting the battery to be permanently sealed once it is filled with acid. Acid pack is included. ALUMINUM WHEEL SPACERS > $63.95 - $98.95 Increase wheel stability by moving wheels out 1” & 1 ½”. Eliminates rubbing against shocks, struts and exhaust. electrical WHEELS & TIRES
10 www.moose-offroad.com BALL JOINT AND KING PIN KITS > $21.95 - $52.95 Ball joint kits offer a considerable cost savings over OEM. Steel housing on some applications replace aluminum joints standard on OEM parts. POM-M90 bearing cup isolates steel rod from housing. OEM does not supply replacement ball joints on many applications. King pin kits are for smaller ATVs where ball joints are not used. Bearings are all hardened steel HIGH-PERFORMANCE BALL JOINT KITS > $57.95 Heavy-Duty Ball Joint Kits feature durable steel on steel design and adjustable end cap, which allows slop to be taken up as they wear. Greased zerk fitting for easy grease delivery. CV BOOT KITS > $10.95 - $15.95 Replace those dangerously worn, inexpensive CV boots before dirt, dust and grime destroy expensive CV joints. Tougher than stock and complete with everything you need to complete the job. Heavy-duty puncture resistant boot. Comes with grease and clamps. Each complete assembly fits one side. LIFT KITS > $169.95 - $299.95 Increases clearance by 1”- 1 ½”. Made of stainless steel. Easy Installation. No special tools required. HEAVY-DUTY GAS SHOCKS > $94.95 - $266.95 Upgrade those oil shocks to heavy duty shocks. Rugged design comes standard with 10% stiffer springs. Adjustable preload settings. Ready to mount, right out of the box. Shocks and struts include springs, retainers and bumpers (where applicable). Sold as each. HIGH CLEARANCE LOWER CONTROL ARMS > $486.95 - $650.95 High clearance lower control arms add 2” of ground clearance. Fabricated from 1.25”, .120” wall DOM tubing and braced to increase strength. CNC machined ball joint block. MIG welded. Durable powder coated finish. Sold as a pair. Page 242 in the 2025 Moose Off Road ATV/UTV catalog. Page 255 in the 2025 Moose Off Road ATV/UTV catalog. Page 249 in the 2025 Moose Off Road ATV/UTV catalog. Page 259 in the 2025 Moose Off Road ATV/UTV catalog. Page 264 in the 2025 Moose Off Road ATV/UTV catalog. Page 260 in the 2025 Moose Off Road ATV/UTV catalog. COMPLETE FRONT AXLE ASSEMBLY > $138.95 - $145.95 The result of quality components and superior engineering. Designed to meet rigid tolerances and to fit OEM applications. Chromoly steel axle bar. Precision ground components. Low profile stainless steel clamps. Assembled with 3% moly grease. Fully assembled outboard and inboard joints. HEAVY-DUTY CV AXLES > $153.95 - $229.95 Exceed OEM quality in fit, form and function. Torture tested to failure to ensure maximum durability. Designed to withstand the most rigorous conditions and terrain. Highest quality, most reliable, and toughest constant velocity axles on the market. Precision machined and heat treated solid chromoly steel center shaft, cages and ball bearings up to 35% stronger. Induction heat treated joints with premium heavy-duty, high temperature moly grease. Precision rolled splines and threads improve fitment and wear. High-strength, spring steel retaining clips (where required). TPE dust boots for superior tear and puncture resistance. All new dust rings and guards (where required). Secure stainless steel dust boot clamps. Fully assembled for easy installation OEM REPLACEMENT CV AXLES > $109.95 - $129.95 Exceed OEM quality in fit, form and function. Torture tested to failure to ensure maximum durability. Designed to withstand the most rigorous conditions and terrain. Manufactured in a state-of-the-art ISO9001 and TS16949 certified factory. Highest quality, most reliable, and toughest constant velocity axles on the market. Precision machined and heat treated solid chromoly steel center shaft, cages, races and ball bearings up to 35% stronger. Induction heat treated joints packed with high performance moly grease. Precision rolled splines and threads. High-strength spring steel retaining clips (where required). All new dust rings and guards (where required.) High quality neoprene rubber dust boots. Secure stainless steel dust boot clamps. Fully assembled for easy installation. Page 208 in the 2025 Moose Off Road ATV/UTV catalog. Page 218 in the 2025 Moose Off Road ATV/UTV catalog. Page 227 in the 2025 Moose Off Road ATV/UTV catalog. COMPLETE AXLES SUSPENSION, DRIVE & CLUTCH
www.moose-offroad.com 11 REAR RADIUS ROD PLATES > $114.95 - $142.95 Replace the thin OEM stock radius rod plate. This plate takes a lot of stress. Replace it with this 5/8” thick billet machined plate. No more flex and you will never have to worry about it breaking or bending. Installs just like the stock unit, no modifications necessary. HIGH-CLEARANCE RADIUS RODS > $253.95 - $582.95 TIG welded. Durable powder coated finish. Fully adjustable to set camber and toe. Heat treated 5/8” heim joints ratedto 17,900 lb. 1 1/4” .125” wall DOM tubing. 416 stainless steel misalignment spacers. HD versions are constructed from massive 11/2” seamless DOM tubing. INDEPENDENT REAR SUSPENSION KITS > $26.95 - $114.95 Cost-effective kit containing all of the parts required to rebuild one side of a rear suspension. Includes all bearings, bushings, seals, shafts and all components to repair the rear upper and lower A-arm and knuckle. Two kits required per vehicle. PROPELLER SHAFTS > $216.95 - $467.95 Direct replacement for the OEM shafts. Heat-treated carbon steel. Long lasting operation. Vibration-free design. Direct OEM replacement. Powder-coated black for extreme durability. Heavy-duty U-joints with greased fittings. Replaceable U-joints. UTV STEERING RACK TIE ROD ASSEMBLY KIT > $14.95 - $88.95 Can save you hundreds of dollars versus the cost of a complete steering rack assembly. The inner rod assemblies have increased shaft diameters to improve strength. Each kit includes heavy-duty inner and outer rod ends with replacement boot, clamps and any required lock washers. Outer tie rod ends are also available individually. • Outer Tie Rod End – contains one tie rod end. This end attaches to the steering knuckle (two required per vehicle). • Rack and Pinion End Kit (left) – contains both tie rod end and shaft that connects to the steering rack as well as the outer tie rod end. Kit also contains a boot and required hardware for the left (driver) side. • Rack and Pinion End Kit (right) – contains both tie rod end and shaft that connects to the steering rack as well as the outer tie rod end. Kit also contains a boot and required hardware for the right (passenger) side. ELECTRIC POWER STEERING KITS > $759.95 - $999.95 Housing is weather sealed to an IP67 submersion ratin and has waterproof connectors. The injection-molded design allows for the EPS to be moisture, debris and vibration resistance. UTV applications come with an adjustable shaft to fine-tune for a perfect fit. No drilling is required for installation. SHOCK BUMPERS AND BLADDER > $19.95 Meets or exceeds OEM standards, but without the OE price. Many are not available separately from the OEM. TIE ROD ENDS > $27.95 - $41.95 Contains inner and outer tie rod ends that are designed toreplace loose and worn out tie rod ends. Two required per vehicle. TIE ROD ASSEMBLY UPGRADE KITS > $99.95 - $102.95 Heavy-duty 12mm style tie rod assemblies. Each kit contains two tie rods, four tie rod ends, cotter pins and jam nuts. Page 265 in the 2025 Moose Off Road ATV/UTV catalog. Page 265 in the 2025 Moose Off Road ATV/UTV catalog. Page 272 in the 2025 Moose Off Road ATV/UTV catalog. Page 274 in the 2025 Moose Off Road ATV/UTV catalog. Page 286 in the 2025 Moose Off Road ATV/UTV catalog. Page 266 in the 2025 Moose Off Road ATV/UTV catalog. Page 264 in the 2025 Moose Off Road ATV/UTV catalog. Page 279 in the 2025 Moose Off Road ATV/UTV catalog. Page 283 in the 2025 Moose Off Road ATV/UTV catalog. SUSPENSION, DRIVE & CLUTCH
12 www.moose-offroad.com PRIMARY CLUTCH BEARINGS > $47.95 - $69.95 Replace that rough of seized primary clutch ONE-WAY needle bearing. Our bearing is a direct replacement and will get your clutch running like new again. Sold Each. CENTER DRIVE SHAFT BEARING ASSEMBLIES > $28.95 - $75.95 More aggressive than the OEM seal. Keeps dirt and water out of the bearing better then OEM. Sold as a complete assembly. STEERING STEM BEARING AND SEAL KITS > $6.95 - $40.95 Drop in replacement to upgrade OEM ball type bearing sets to taper bearings. Tapered roller bearings provide decreased maintenance, less wear, smooth operation and longer life. Comes complete with both upper and lower taper bearing cups, cones and seals. WHEEL BEARING KITS > $7.95 - $66.95 Includes all bearings and seals required to rebuild one wheel. EMQ premiumquality, high-speed bearings feature double-lip rubber seals. Specifically designed to keep out dirt and water while providing superior grease retention. Seals contain a garter-spring inner lip that guarantees an optimum seal. CRANKSHAFT BEARINGS > $18.95 - $79.95 OEM matched, high-quality bearing/seal kit. Includes all bearings and seals required to do a crank at a fraction of OEM cost. BILLET PROP SHAFT BEARING CARRIER > $149.95 Made from 6061 billet aluminum. Incorporates a greasable high speed bearing. Reduces driveline misalignment. Offers additional support and strength for the prop shafts. Will outlast and outperform the cheap OEM bearing carrier. Mounting hardware and instructions included. TAPERED DAC WHEEL BEARING UPGRADE KITS > $53.95 95% better static and 86% better dynamic load capacity compared to standard dac bearings. High-contact double-lip seals with armor shield. O-ring seals on id of bearing for superior water and dirt exclusion. 52100 bearing steel hardened and tempered for maximum durability. Page 301 in the 2025 Moose Off Road ATV/UTV catalog. Page 306 in the 2025 Moose Off Road ATV/UTV catalog. Page 307 in the 2025 Moose Off Road ATV/UTV catalog. Page 307 in the 2025 Moose Off Road ATV/UTV catalog. Page 308 in the 2025 Moose Off Road ATV/UTV catalog. Page 316 in the 2025 Moose Off Road ATV/UTV catalog. Page 310 in the 2025 Moose Off Road ATV/UTV catalog. UTV STEERING RACK KIT > $129.95 - $139.95 Replaces an OEM rack at a fraction of the price of OEM. Includes rack assembly, inner tie rod ends and tie rods. Compatible with OEM and Moose Utility Division® Tie Rods, Boots and Tie Rod Ends. Does not include outer ends (available separately). HEAVY-DUTY U-JOINTS > $23.95 - $33.95 Heavy-duty construction. HIGH PERFORMANCE PLUS BELTS > $39.95 - $155.95 Armid Cord provides strength and durability. Specially formulated compounds that work best for each application. Made in the USA. INNER AND OUTER CLUTCH COVERS > $129.95 - $172.95 Quality replacement inner and outer clutch covers. These covers simply bolt on in place of the factory cover. BELT INNER CLUTCH COVER GUARDS > $82.95 Provides protection during rides from the impact of broken belt. Made from high-quality 2mm stainless steel with silver baking varnish. Rust and corrosion resistant, while being sturdy and durable. Designed with multiple rolling angles to perfectly fit belt cover and features high-end appearance of shiny silver paint finish on both sides. STARTER DRIVES > $91.95 - $197.95 Replaces OEM starter drive. Page 280 in the 2025 Moose Off Road ATV/UTV catalog. Page 290 in the 2025 Moose Off Road ATV/UTV catalog. Page 298 in the 2025 Moose Off Road ATV/UTV catalog. Page 300 in the 2025 Moose Off Road ATV/UTV catalog. Page 299 in the 2025 Moose Off Road ATV/UTV catalog. Page 296 in the 2025 Moose Off Road ATV/UTV catalog. SUSPENSION, DRIVE & CLUTCH BEARINGS
www.moose-offroad.com 13 TRANSMISSION BEARING AND SEAL KITS > $29.95 - $199.95 Kit contains all of the bearings, seals, o-rings and shims as required to rebuild the transmission. Direct oem replacement at a fraction of the cost. High quality ABEC 3 precision ball bearings used throughout Kits containing tapered bearings include shim selection. SWINGARM BEARING KITS > $29.95 - $59.95 OEM replacement parts designed to rebuild the swing arm to factory specification. Kit contains bearings, seals, spacers and pins. FRONT A-ARM BEARING AND SEAL KITS > $13.95 - $78.95 OEM replacement designed to rebuild the A-arm to factory specification. Contains bearings, pins, spacers and seals. DIFFERENTIAL BEARINGS AND SEAL KITS > $9.95 - $133.95 Kits include high-speed bearings that are premium-quality and use EMQ standard seals. Garter-spring inner lips and optimal sealing from rubber-covered outside diameter seals. SEAL KIT ONLY BEARING & SEAL KIT FRONT AND REAR SHOCK BEARING AND BUSHING KITS > $14.95 - $18.95 OEM replacement parts designed to rebuild the shock to factory specification. Kit contains bearings, seals, spacers and pins. QUALIFIER XCR BRAKE SHOES QUALIFIER BRAKE PADS > $16.95 Latest generation of Kevlar® based organic material. Progressive feel and rider feedback. No rotor wear and quiet. BRAKE PADS & SHOES Pads are constructed of durable sintered metal which stands up to the toughest conditions and provides equal braking power, wet or dry. Brake shoes are asbestos-free and offer durability and performance. XCR BRAKE PADS > $16.95 - $46.95 Ultimate wet condition pads. Low-wear S-47 sintered metal compound outlasts the gnarliest conditions. High-tech gray zirconium-based ceramic applied extra thick to protect brake fluid from heat. OEM REPLACEMENT ROTORS > $109.95 Manufactured from 420 high carbon stainless steel. Engineered to offer greater strength and durability than OEM. Offers greater friction and longer life than OEM rotors. CAD/ CAM laser-cut and finish-ground for a distortion-free flat profile. Quality replacement for worn/warped stock rotors when superior braking is a must. Made in the USA. Manufactured by: BILLET MASTER CYLINDER COVERS > $29.95 6061 aluminum. OEM replacement part. Made in the USA. MASTER CYLINDER COVER PLATES > $21.95 Replaces the stock reservoir cover. Adds a finishing touch to your ATV. Made in the USA. BEARING GREASERS > $39.95 Polaris wheel bearings are notoriously low on grease from the factory. Now you can quickly and easily add grease to your wheel bearings. 44mm greaser is designed to service Polaris 44mm ID wheel bearings. Decrease wheel bearing temps while increasing longevity by periodically re-greasing your wheel bearings. No need to remove the axles, this tool simply slides over the axle and into the hub for easy greasing. 40mm greaser is designed to service Polaris 40mm ID wheel bearings. Billet aluminum construction with multiple grease grooves make the job quick, clean, and easy. Manufactured by: Page 325 in the 2025 Moose Off Road ATV/UTV catalog. Page 327 in the 2025 Moose Off Road ATV/UTV catalog. Page 338 in the 2025 Moose Off Road ATV/UTV catalog. Page 438 in the 2025 Moose Off Road ATV/UTV catalog. Page 328 in the 2025 Moose Off Road ATV/UTV catalog. Page 349 in the 2025 Moose Off Road ATV/UTV catalog. Page 360 in the 2025 Moose Off Road ATV/UTV catalog. Page 369 in the 2025 Moose Off Road ATV/UTV catalog. Page 373 in the 2025 Moose Off Road ATV/UTV catalog. Page 373 in the 2025 Moose Off Road ATV/UTV catalog. catalog BEARINGS BRAKING
14 www.moose-offroad.com MECHANICAL WATER PUMP SEALS > $18.95 - $33.95 High quality mechanical water pump seals now available separately. Enhances our existing complete gasket kit. WATER PUMP REBUILD KITS > $22.95 - $120.95 Includes every gasket, O-ring, bearing and seal required to rebuild a water pump. Page 400 in the 2025 Moose Off Road ATV/UTV catalog. Page 403 in the 2025 Moose Off Road ATV/UTV catalog. FUEL PUMP MODULE > $166.95 - $192.95 Complete automotive quality fuel pump is an exact replacement. Installs in the stock location and will maintain the proper operation and life of your fuel system. Drop in the tank and plug it in. Page 393 in the 2025 Moose Off Road ATV/UTV catalog. Page 398 in the 2025 Moose Off Road ATV/UTV catalog. Page 394 in the 2025 Moose Off Road ATV/UTV catalog. Page 395 in the 2025 Moose Off Road ATV/UTV catalog. Page 397 in the 2025 Moose Off Road ATV/UTV catalog. FUEL PUMPS > $24.95 - $53.95 CARBURETED AND EFI. Direct replacement fuel pumps. Available for EFI or carbureted models. Stock flow rates. Pick up screen/filters included. FUEL PRESSURE REGULATORS > $49.95 Regulates the fuel delivery to a constant PSI.All regulators are set to the stock pressure settings. Includes a new sealing O-ring. Works in conjunction with corresponding fuel pump. FUEL PUMP STRAINERS > $13.95 installs over a small pickup on the fuel pump and is held in place by a press fit retainer. Installs in the stock location and will maintain the proper operation and life of your fuel pump. FUEL PETCOCK REBUILD KITS > $12.95 - $17.95 Includes components to rebuild one fuel petcock. Kits include all necessary face screws, tank bolts, face gasket, tank gasket, diaphragm, O-rings, wave washer and miscellaneous components. Kits for non-rebuildable riveted Honda fuel taps include special drill and self-tapping screws along with instructions for easy and inexpensive rebuild. FUEL INJECTORS > $32.95 - $54.95 Replace those dirty, clogged or malfunctioning injectors. Stock injectors are epoxied to the wire harness so we include our own replacement wire harness. Sold each. HIGH PERFORMANCE 4-STROKE PISTON KITS BY CP PISTONS > $461.95 - $479.95 Pistons feature x-style forgings and fully boxed-style (race pistons). Forgings come standard with skirt coating which reduces friction, which in return reduces heat. Our race piston kits include DLC pin. Internalbracing maximizes durability while decreasing friction in the pin assembly. This technology had been proven and used because of its high resistance to abrasive wear, which extends the service life and reliability under extreme conditions. Full radius dome designs maximize quench while eliminating hot spots that promote detonation. Each kit includes a piston, wrist pin, circlips and a top end gasket kit. Made in the USA. TOP END GASKET SETS COMPLETE GASKET SETS COMPLETE SET W/OIL SEALS AND OIL SEAL SET > $11.95 - $223.95 Each set includes high-performance head, base, intake and exhaust gaskets. Our performance sets are designed for a completetop-end rebuild. Made of high-tech materials providing unmatched reliability and performance. Clutch cover gaskets also availabe separately. Made in the USA. FLOAT BOWL GASKETS > $7.95 Direct OEM replacement. Sold each. EXHAUST GASKET KITS > $5.95 - $10.95 2-stroke kits include O-rings, springs, washer and gasket(where applicable). 4-stroke kits contains header gasket. CLUTCH COVER GASKETS, SCREWS AND PLUGS > $9.95 - $24.95 Getting water in your clutches is a major pain and will cause major problems if it happens out on the trail. Replace that worn or torn gasket now. Screws are an OEM replacement. CARBURETORS > $69.95 - $179.95 Direct replacement complete carburetors. Fully assembled and ready to install using all the OEM cables. An excellent alternative to the expensive OEM carburetors. Comes pre-jetted but may require some additional tuning. CARBURETOR REPAIR KITS > $16.95 - $59.95 Kit includes all of the necessary components to repair a carburetor. Includes all O-rings, gaskets, jets, needle, mixture screw, float bowl screws, float valve needle and seat OEM jet sizes. NBR rubber material is used on all O-rings and rubber gaskets. NBR has excellent resistance to the ethanol used in today’s fuels. Page 376 in the 2025 Moose Off Road ATV/UTV catalog. Page 388 in the 2025 Moose Off Road ATV/UTV catalog. Page 390 in the 2025 Moose Off Road ATV/UTV catalog. Page 385 in the 2025 Moose Off Road ATV/UTV catalog. Page 383 in the 2025 Moose Off Road ATV/UTV catalog. Page 391 in the 2025 Moose Off Road ATV/UTV catalog. ENGINE
www.moose-offroad.com 15 REPLACEMENT COOLING FANS > $112.95 - $274.95 Easily installs using original mounting hardware. All fans are waterproof and dustproof. All fans (except Polaris fans) are typically 25% higher CFM than the stock fan. CFM = cubic feet per minute; it’s a rating used to tell how much airflow a fan has. The Polaris fans are OEM compatible in design and output. Less expensive than factory replacements with more performance. AIR FILTERS > $6.95 - $64.95 Engineered for maximum air flow while increasing horsepower. Maintains premium protection by stopping the finest dust particles. Made of dual bonded foam for easier cleaning. Flexible seams that will not crack. Filters are designed to fit all stock air boxes. Made in the USA. PPO (PRECISION PRE-OILED) AIR FILTERS > $7.95 - $66.95 Same high-quality filters available pre-oiled. High technology machine pre-oils filter to perfection while leaving no excess. Includes re-sealable filter bag. Made in the USA. OIL FILTERS > $5.95 - $8.95 High-quality replacement for your standard filter. Manufactured with sealing ring to ensure perfect fit. Can filter down to 10 microns. Offers maximum protection and long lasting filter life. May be used with conventional and synthetic oils. RADIATOR CAPS > $15.95 Automotive-quality replacement 13 PSI caps. Stamped steel cap with rubber bottom seal. Page 409 in the 2025 Moose Off Road ATV/UTV catalog. Page 410 in the 2025 Moose Off Road ATV/UTV catalog. Page 410 in the 2025 Moose Off Road ATV/UTV catalog. Page 407 in the 2025 Moose Off Road ATV/UTV catalog. Page 412 in the 2025 Moose Off Road ATV/UTV catalog. Page 399 in the 2025 Moose Off Road ATV/UTV catalog. OXYGEN SENSORS > $49.95 - $100.95 Monitor oxygen levels in exhaust gases, enabling real-time adjustments to fuel injection and ignition timing for optimal engine performance. Page 46 in the 2025 Moose Off Road ATV/UTV catalog. Page 54 in the 2025 Moose Off Road ATV/UTV catalog. CHAINSAW BRACKET > $183.95 - $184.95 Machined out of solid high density polyethylene for maximum durability. Mount your chainsaw vertically for simple safe transport. Bracket includes 2 Quick Detachable anchors and installation hardware to mount it on bed rails and cargo racks. Chainsaw not included. Made in the USA. CAN-AM FRONT AND REAR DOOR BAGS > $69.95 - $74.95 Front bag mounts to factory door using self-fastening straps. Protective front knee pad is removable. Rear bag mounts using rear factory door holes, hardware and self-fastening straps. Sold as set. FRONT REAR TWIST N LOCK TIE DOWN ANCHORS > $48.95 Twist lock anchors include eye nuts on the top for your tie down. Simply insert the anchors in the bed hole of your Ranger/General or RZR/Sportsman; tighten and go. Great for tying down loads and gear. RZR/Sportsman sold in 4-packs, Ranger/Defender/General sold in 2-packs. Made in the USA. FLAG MOUNTS> $29.95 - $42.95 Includes the integrated Twist Lock Anchor, grey machined base mount, all hardware and coupling nut. Simple drop-andtwist installation in your bed hole. Also accommodates most other flag bases and spring mounts. Made in the USA. Page 74 in the 2025 Moose Off Road ATV/UTV catalog. Page 432 in the 2025 Moose Off Road ATV/UTV catalog. Page 33 in the 2025 Moose Off Road ATV/UTV catalog. Page 437 in the 2025 Moose Off Road ATV/UTV catalog. CAN-AM X3 BELT CHANGING TOOL > $54.95 Portable belt changing tool allowing belt to be changed quickly during the journey. Smooth roller design for quick and effortless removal and reinstallation. CNC machined from billet 6061 aluminum with high hardness and lightweight, anodized black finish. REAR RECEIVER HITCHES > $85.95 2” reciever hitches are frame mounted with a durable powdercoated finish. Provides heavy towing capabilities. Made in the USA. ENGINE GARAGE
3501 KENNEDY ROAD | JANESVILLE, WISCONSIN 53545 MOOSE OFFROAD IS A REGISTERED TRADEMARK. ALL RIGHTS RESERVED. COPYRIGHT 2025. LEMANS CORPORATION. THESE MATERIALS MAY NOT BE COPIED OR REPRODUCED IN ANY MANNER WITHOUT WRITTEN PERMISSION OF LEMANS CORPORATION. PRINTED IN THE USA. distributed exclusively by: MOOSE-OFFROAD.COM
www.moose-offroad.comRkJQdWJsaXNoZXIy