BOLD MAGENTA part numbers are new for 2023 DRAGSPECIALTIES.COM 2023 | TIRE & SERVICE V-TWIN TOOLS 604 PART # DESCRIPTION SUG. RETAIL 3801-0318 For 17-20 M-Eight and 99-17 Twin Cam $87.95 CYLINDER HOLD DOWN NUTS • Help to keep the cylinders in place when removing the heads from the engine • One end fits Twin Cam models and the other fits M-Eight engines • Sold in a set of two • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0345 For 17-20 M-Eight 107”, 114” $671.95 3801-0130 For 99-17 Twin Cam 88”, 96” or 103”, 3.75”-3.875” 653.95 3801-0129 For 99-17 Twin Cam Screamin’ Eagle, 4”-4.060” 636.95 DS-196212 For 66-99 Big Twin cylinders, 3.4375”-4” bore w/ stock bolt pattern 644.95 DS-196213 Adapter bolt kit for 86-03 XL, 94-03 Buell (for use w/ PART #DS-196212) 51.95 CYLINDER TORQUE PLATES • Torque plates must be used when boring or honing late-model aluminum cylinders • Simulate running stress conditions • Instructions included • Made in the U.S.A. 3801-0345 DS-196212 PART # DESCRIPTION SUG. RETAIL 53-0005 For 58-99 Big Twin motors (except Twin Cam) $39.95 CRANKPIN NUT CLEARANCE GAUGE • Used to mark clearance between the cases and crankpin nuts when using stroker flywheels • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196155 For 57-85 XL $56.95 TAPPET GUIDE PULLER TOOL • Used to remove press-fit tappet guides from crankcase • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0251 Tappet adjustment tool $36.95 TAPPET GO-NO-GO TOOL • Simplifies the way to verify proper tappet adjustment • If the tip doesn’t fit between the clip and the pushrod seat or if there is up and down end play, then the tappet is out of adjustment • For use on most hydraulic tappets, OEM and aftermarket, for Twin Cam or Evo • Will not work on Solids, JIMS Hydrosolids or other limited travel tappets • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0192 Tappet pump and test stand for 99-20 Big Twin hydraulic tappets $338.95 3801-01931 Adapter for 84-99 Evo hydraulic tappets 86.95 1 Must be used in conjunction with PART #3801-0192. TAPPET PUMP AND TEST STAND • Allows you to fill hydraulic tappets before assembling valve train • Helps diagnose loose or spongy tappets that could eventually lead to bleed-down issues or sticky tappets that won’t pump up due to poor hydraulic unit fitment • Made in the U.S.A. 3801-0193 3801-0192 PART # DESCRIPTION SUG. RETAIL 3801-0292 For 84-20 Big Twin hydraulic tappet assemblies $101.95 VACUUM LIFTER PUMP UP TOOL • Bleeds and pumps up hydraulic lifters • Special jar, designed for vacuum, holds up to four hydraulic lifters in a convenient tray • Apply the vacuum to fully bleed the lifters and have them ready to install • Removes the risk of using the starting system to pump up the lifters or damage to the valve train at low rpm if the lifters are not fully bled • Made in the U.S.A.
RkJQdWJsaXNoZXIy OTcxOTk3