BOLD MAGENTA part numbers are new for 2023 V-TWIN TOOLS DRAGSPECIALTIES.COM TIRE & SERVICE | 2023 611 PART # DESCRIPTION SUG. RETAIL 3801-0252 For 17-22 M-Eight oil pumps and 99-17 Twin Cam camplates $119.95 REAMER TOOL FOR PSI RELIEF VALVE BORE • Use this reamer to perform a ‘valve job’ on the pressure relief valve seat of all M-Eight oil pumps and Twin Cam engine camplates • Lightly machine (clean) the relief valve seat and re-seat the plunger valve • Feuling recommends the valve to be seated and sealed from 0-30 psi with a full pop off psi of 55-60 psi • Best used in conjunction with Feuling® pressure testing tool PART #3801-0071 for Twin Cam camplates • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196144 For 70-99 Big Twin (except Twin Cam) $125.95 CAM COVER HOLDING TOOL • Clamps in vise • Holds cam cover flat and helps prevent damage/ scratches when removing and installing bushings • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196170 For 70-99 74” and 80” Big Twins, and 70-03 XL models $20.99 CAM COVER PULLER • Designed to remove the cam cover • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196198 For 00-06 Twin Cam motors (except 06 FXD) $218.95 3801-0061 For 06 Dyna and all 07-17 Twin Cam 325.95 DS-196156 For 58-99 Big Twin, except Twin Cam 229.95 DS-197056 For 57-90 XL 228.95 INNER CAM BEARING REMOVAL TOOLS • Used to remove inner cam bearing without damaging the crankcase • Tool is also designed to keep rollers from falling into the crankcase • Instructions included • Made in the U.S.A. 3801-0061 PART # DESCRIPTION SUG. RETAIL DS-196193 For 99-06 Twin Cam (except 06 Dyna) for removal of bearings; for L00-06 FXST/FL and L00-05 FXD for removal of front cam bearing $295.95 CAM BEARING PULLER • Use to remove the cam ball bearings from the camshafts after they are removed from the support plate PART # DESCRIPTION SUG. RETAIL 3801-0066 For 06 Dyna and all 07-17 Twin Cam $211.95 CAM ASSEMBLY TOOL • Holds both cams in an upright position while lowering cam support plate over both guides and cam journal guides • Made from a non-marring material that will not damage cam surface • Made in the U.S.A. • Removes bearing straight without binding or slipping • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196199 For 99-06 Twin Cam (except 06 Dyna) for removing/installing cams and bearings; for 00-06 FXST/FL and L00-05 FXD to remove and install cams only $239.95 CAMSHAFT REMOVAL/ INSTALLATION TOOL • Used to remove and install camshafts and bearings • Provides precision alignment of camshafts in the support plate • Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0316 For 17-20 M-Eight $327.95 CAMSHAFT NEEDLE BEARING REMOVER/INSTALLER • Correctly and accurately replaces the camshaft inner needle bearing in M-Eight engines • Uses the proven JIMS-style remover collet and fine-threaded installation driver • Removal hole allows you to see what you’re doing while using the tool • Holds tighter tolerances, allowing more precise installation depth • Made in the U.S.A.
RkJQdWJsaXNoZXIy OTcxOTk3