BOLD MAGENTA part numbers are new for 2024 DRAGSPECIALTIES.COM 2024 | TIRE & SERVICE V-TWIN TOOLS 608 SPROCKET SHAFT BEARING RACE TOOL • Used to remove and install Timken® bearing race on motor cases •Uses drivers with handle PART #DS-196042 •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL BEARING RACE TOOL DS-196046 For 69-02 Big Twin $104.95 DS-196045 For 77-03 XL, 94-02 Buell 104.95 DRIVER HANDLE DS-196042 Handle/driver only (ea.) 110.95 DS-196042 DS-196046 PART # DESCRIPTION SUG. RETAIL 3802-0066 For 91-20 XL and Buell (except Buell 1125R) $95.95 XL SPROCKET NUT SOCKET TOOL • Short socket is specifically designed to remove, install and properly tighten the front final drive sprocket/pulley •Ensures mainshaft on the XL extends through the guidance collar for correct alignment •Provides full contact to the nut when tightening •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-198637 For 55-06 Big Twin $63.95 SPROCKET SHAFT PROTECTOR CAP •Protects sprocket shaft when using crank assembly removing tool PART #DS-196089 or a press •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 1/2” DRIVE DS-196104 For crankpin nut OEM #23969-83; L83-99 Big Twin 1 1/2” $108.95 DS-196111 For pinion shaft nut OEM #24016-80; 81-89 Big Twin 1 1/4” 108.95 3/4” DRIVE DS-196110 For sprocket shaft nut OEM #24017-80; 72-99 Big Twin 1 5/8” 118.95 FLYWHEEL SOCKETS •Made of 4130 chromoly steel •Available in 1/2” or 3/4” drive •Machined for 100% nut-to-socket and drive-end contact •Eliminates nut rounding and risk of injury •Made in the U.S.A. DS-196104 DS-196111 DS-196110 PART # DESCRIPTION SUG. RETAIL 3801-0088 Bearing and race puller tool $426.95 BEARING AND RACE PULLER TOOL •Multi-faceted tool has many uses • Removes flywheel sprocket shaft inner bearing race on 03-07 Twin Cam • Can be used to remove Timken® bearing (OEM #9028 or #9029) on 55-07 Big Twins, including JIMS 120” engines • Can be used to remove Timken bearing pinion shaft inner bearing race on 57-07 XL, including all Buells •Can also be used to remove press-fit transmission gears and bearings from input and output shafts on all 02-07 V-Rod models •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0293 For 15-16 Indian Scout $101.95 FLYWHEEL PULLER TOOL •Ensures good and solid engagement when using the puller •Eliminates potential damage to the flywheel when used in this application •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL 3801-0322 For 17-20 M-Eight $248.95 MAIN BEARING REMOVER/INSTALLER •Removes left and right main bearing without damaging case •Provides correct alignment and depth during installation •Made in the U.S.A. PART # DESCRIPTION SUG. RETAIL DS-196194 For 99-02 Twin Cam “A” motors $258.95 CRANKSHAFT BEARING TOOL •Used to remove and install the right crankcase bearing in Twin Cam motors • Allows straight installation, without damage to the case •Includes instructions •Made in the U.S.A. STATOR ADAPTER MAIN BEARING TOOL •This adapter is a simple time and money saver when installing JIMS main bearing on a Milwaukee Eight® left side crankcase •When this adapter is used in conjunction with the main bearing tool (3801-0322), or OE tool, the stator can remain attached to the left side case during bearing installation •The adapter has been designed with added clearance for the stator screw, which are one time use only screws •It will also guarantee that the case plug seal of the stator is not compromised resulting in a leak • Manufactured from quality 1144 steel, plated in black oxide for corrosion resistance •Simply position this adapter on top of the bearing support on the press table •Made in the U.S.A PART # DESCRIPTION SUG. RETAIL 3801-0424 For 17-22 M-Eight $67.95
RkJQdWJsaXNoZXIy OTcxOTk3