BOLD MAGENTA part numbers are new for 2025 FUEL/AIR SYSTEMS PARTS-UNLIMITED.COM OFFROAD | 2025 FUEL/AIR SYSTEMS 1587 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. DESCRIPTION PART # Small engine fuel line variety pack 0706-0454 SMALL ENGINE FUEL LINE VARIETY PACK •Designed for small diameter fuel lines •Remains flexible and will not crack or harden when in use •Contains one each of the following sizes: 5/64”, 3/32”, and 1/8” NOTE: Not compatible with fuel containing more than 10% ethanol. DESCRIPTION PART # 1/8” ID – 3’ LENGTH Clear 0706-0138 3/16” ID X 5/16” OD – 3’ LENGTHS Black 0706-0044 Clear 0706-0041 Gray 0706-0038 1/4” ID X 7/16” OD – 3’ LENGTHS Black 0706-0045 DESCRIPTION PART # 1/4” ID X 7/16” OD – 3’ LENGTHS (CONT) Clear 0706-0042 Gray 0706-0039 5/16” ID X 1/2” OD – 3’ LENGTHS Black 0706-0046 Clear 0706-0043 Gray 0706-0040 DESCRIPTION PART # 1/8” ID – 25’ ROLL Clear 0706-0139 3/16” ID X 5/16” OD – 25’ ROLLS Black 0706-0018 Clear 0706-0021 Gray MP12-031 1/4” ID X 7/16” OD – 25’ ROLLS Black 0706-0019 DESCRIPTION PART # 1/4” ID X 7/16” OD – 25’ ROLLS (CONT) Clear 0706-0022 Gray MP12-032 5/16” ID X 1/2” OD – 25’ ROLLS Black 0706-0020 Clear 0706-0023 Gray MP12-033 PREMIUM FUEL LINES •Stronger and more durable than vinyl fuel line •Use with any type of gasoline •Resists swelling and hardening • Resistant to direct sunlight, hardening and/or cracking •Flexible in temperatures from -35 ° F to +165 ° F •Fuel line stretches easily over fittings or petcocks DESCRIPTION PART # 1/4” ID 3’ L 0706-0204 25’ L 0706-0206 DESCRIPTION PART # 5/16” ID 3’ L 0706-0205 25’ L 0706-0207 LP (LOW PERMEATION) PREMIUM FUEL LINE •Certified to meet permeation emission standards of 15g/M2/d ay • On emission-controlled vehicles, check with local and state agencies to determine suitability •Robust multi-layer design and construction •Fluoropolymer liner compatible with higher ethanol-blend gasoline up to 100% • Highly flexible, easy to install and offers excellent fitting retention • Resistant to swelling, hardening and cracking caused by hydrocarbon-based fluids •Ozone and UV light resistant •Wide temperature range from -20 °F to 165 °F (-28.9 °C to 73.9 °C) •Yellow color for easy identification •Use Stepless® Clamps NOTE: Not for use with fuel injection systems. NOTE: #SNG-ENAPNR-OA-03. NOTE: Exempt per EPA CARB E.O. #Q-09-028 for off-road use. CARBURETOR FUEL LINE (NON-SUBMERSIBLE) ID PART # 2’ LENGTH 3/16” 0706-0176 3/8” 0706-0179 ID PART # 25’ LENGTH 3/16” 0706-0180 1/4” 0706-0181 ID PART # 25’ LENGTH (CONT) 5/16” 0706-0182 3/8” 0706-0183 FUEL INJECTION FUEL LINE (NON-SUBMERSIBLE) ID PART # 25’ LENGTH 1/4” 0706-0185 ID PART # 25’ LENGTH (CONT) 5/16” 0706-0187 LP (LOW PERMEATION) FUEL LINES •Five-layer Greenshield™ barrier technology keeps fuel out of the environment, while delivering peak fuel efficiency • Heat-, oil-, ozone- and abrasion-resistant cover • Sold in 25’ rolls and 2’ lengths •Carburetor and fuel-injection line meets EPA 40 CFR 1051.110 and CARB E.O. #Q-09-019 for low-permeation fuel lines, for offroad use •Fuel-injection line is recommended for any fuel-injection applications •Do not submerse in gasoline NOTE: Carburetor line is not for use on pressure lines on fuel-injection systems or cooling system applications. • Sold in 3’ lengths and 25’ rolls •Made in the U.S.A. NOTE: Not for use with fuel-injected models. Gray Clear Black
RkJQdWJsaXNoZXIy OTcxOTk3